Weider WESY19611 Inside of the Press Cable, Nylon Jamnut the Cable must be able to pivot Freely

Page 17

41. Attach two 3 1/2” Pulleys (15) and two Cable

41

 

33

 

Traps (66) to the end of the Resistance Bracket

 

 

 

 

 

 

(35) as shown with a 3/8” x 3” Bolt (93) and a 3/8”

 

66

 

15

Nylon Jamnut (33). Do not tighten the Nylon

 

 

 

 

 

 

Jamnut yet. Make sure the Pulleys and Cable

 

 

 

 

Traps are oriented as shown.

 

66

 

 

 

 

 

 

Route the Resistance Cable (27) over the indicat-

 

15

 

 

ed 3 1/2” Pulley (15). Make sure that the Cable

 

93

 

 

is between the Pulley and the Cable Trap (66),

 

35

 

 

 

 

and that the Cable Trap is turned to hold the

 

 

27

 

Cable in place.

 

 

 

42. Pull the indicated 3/8” x 3” Grade 5 Bolt (98) out

42

 

 

 

of the wide bracket on the Base (4) until you can

 

 

 

 

 

 

 

remove the indicated 3 1/2” Pulley (15). Wrap the

 

 

 

 

Resistance Cable (27) up around the Pulley and

 

 

 

 

then fully reinsert the Bolt.

 

 

 

 

 

 

4

 

 

 

 

27

 

 

 

 

15

98

 

 

 

 

 

43. Route the Resistance Cable (27) over the other

43

35

 

 

3 1/2” Pulley (15) on the Resistance Bracket (35).

 

 

 

 

 

Make sure that the Cable is between the

66

 

 

 

Pulley and the Cable Trap (66), and that the

 

 

 

 

Cable Trap is turned to hold the Cable in

27

 

 

 

place.

15

 

 

 

 

 

 

 

 

 

Refer to step 41. Tighten the 3/8” Nylon

 

 

 

 

Jamnut (33).

 

 

 

 

44. Slide the end of the Resistance Cable (27) onto

44

 

 

 

the indicated 3/8” x 3” Grade 5 Bolt (98), on the

 

 

 

 

 

 

 

outside of the wide bracket on the Base (4).

 

 

 

 

Note: Be sure the Resistance Cable is on the

 

 

 

 

inside of the Press Cable (58).

 

 

 

 

Tighten a 3/8” Nylon Jamnut (33) onto the 3/8” x

 

 

 

 

3” Grade 5 Bolt (98). Do not overtighten the

 

 

 

 

Nylon Jamnut; the Cable must be able to pivot

 

 

 

 

freely.

 

58

 

 

 

 

 

 

 

 

27

 

 

 

 

33

98

4

 

17

 

 

 

Image 17
Contents Model No. WESY19611 Serial No QUESTIONS?Table of Contents Important Precautions Before YOU Begin Make Assembly Easier for Yourself AssemblyTighten all of the 5/16 Nylon Locknuts 3 used in steps 1 to Nylon Locknuts yetLocknuts yet Nylon Locknut the Press Frame must be able to pivot freely ARM AssemblyNylon Locknut yet Arm. Arm identification is very important for StepNylon Jamnut the Leg Lever must be able to pivot freely Tighten the four 5/16 Nylon Locknuts 3 used in this stepNylon Locknut the Rocker Arm must be able to pivot freely Cable is between the Pulley and the hook Not shown Cables. Important While assemblingIdentify the High Cable 23. Wrap the High Page Trap is turned to hold the Cable in place Stabilizer is wrapped around the Weight TubePage 15 66 Page Do not attach a Nylon Jamnut not shown yet Nylon Jamnut the Cable must be able to pivot Freely Inside of the Press CableThat the Press Adjustment Tube is oriented as Shown Seat AssemblyChanging the Weight Setting AdjustmentsAttaching the LAT BAR or Nylon Strap to the Pulley Stations Tightening the Cables TROUBLE-SHOOTING and Maintenance3 2 Weight Resistance ChartWeight Stack Cable DiagramsLow Cable High Cable Resistance CableRound Inner Cap R0102A Part Identification CHART-WESY19611Page Key No. Qty Description Part LIST-Model No. WESY19611Exploded DRAWING-Model Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty