Weider WESY19611 user manual

Page 15

33.Route the Press Cable (58) between the indicat- ed 3 1/2” Pulley (15) and the Cable Trap (66) attached to the Rear Upright (56). Make sure that the Cable Trap is turned to hold the Cable in place. Properly tighten the 3/8” Nylon Locknut (21).

34.Attach the end of the Press Cable (58) to the Long “U”-Bracket (57) with a 1/4” Nylon Locknut

(2)and a 1/4” Washer (10) (see the inset draw- ing). Do not completely tighten the Nylon

Locknut; it should be threaded onto the end of the Cable until only two threads are show- ing above the Nylon Locknut, as shown in the inset drawing. Note: It may be necessary to remove the 3 1/2” Pulley (15) from the Long “U”-Bracket to do this step.

35.Attach the Resistance Bracket (35) inside of the upper bracket on the Front Upright (42) with a 3/8” x 2 1/4” Bolt (14) and a 3/8” Nylon Locknut

(21).Do not overtighten the Nylon Locknut; the Bracket must be able to pivot easily.

See the inset drawing. Remove the indicated 3/8” x 1 1/4” Bolt (83) and 3/8” Nylon Jamnut (33) from the Resistance Handle (88). Attach the Cylinder (89) to the Resistance Handle with the Bolt and the Nylon Jamnut.

Note: The Cylinder (89) should be turned so that the decal is on the same side as the knob on the Resistance Handle (88).

36.Pull out the knob on the Resistance Handle (88) as far as it will go. Slide the Resistance Handle onto the Resistance Bracket (35) and release the knob so that the pin on the knob is inserted into the upper adjustment hole in the Resistance Bracket. Tighten the four Nylon Jamnuts (not shown) on the Handle. Note: Do not overtighten the Nylon Jamnuts; the Handle must be able to slide across the Bracket easily.

Attach the Cylinder (89) and two 5/8” x 7/8” Spacers (61) inside of the lower bracket on the Front Upright (42) with a 3/8” x 3 1/4” Bolt (68) and a 3/8” Nylon Locknut (21) (refer to the inset drawing).

33

 

 

 

56

15

 

 

58

 

 

 

66

 

 

 

 

21

 

 

34

 

 

 

15

 

 

 

2

 

 

 

10

 

 

 

57

 

 

 

58

 

 

2

 

 

 

 

 

58

57

35

 

 

 

88

 

35

42

 

 

 

 

 

21

Knob

33

 

 

83

 

14

 

89

 

 

 

Decal

 

 

 

36

88

 

 

 

 

 

Knob

 

 

 

35

42

 

 

89

 

 

 

 

89

21

 

 

68

 

 

 

61

 

 

 

 

 

 

68

 

61

21

61

 

 

 

 

 

 

15

Image 15
Contents Model No. WESY19611 Serial No QUESTIONS?Table of Contents Important Precautions Before YOU Begin Make Assembly Easier for Yourself AssemblyNylon Locknuts yet Locknuts yetTighten all of the 5/16 Nylon Locknuts 3 used in steps 1 to Nylon Locknut the Press Frame must be able to pivot freely ARM AssemblyNylon Locknut yet Arm. Arm identification is very important for StepTighten the four 5/16 Nylon Locknuts 3 used in this step Nylon Locknut the Rocker Arm must be able to pivot freelyNylon Jamnut the Leg Lever must be able to pivot freely Cables. Important While assembling Identify the High Cable 23. Wrap the HighCable is between the Pulley and the hook Not shown Page Trap is turned to hold the Cable in place Stabilizer is wrapped around the Weight TubePage 15 66 Page Do not attach a Nylon Jamnut not shown yet Nylon Jamnut the Cable must be able to pivot Freely Inside of the Press CableThat the Press Adjustment Tube is oriented as Shown Seat AssemblyChanging the Weight Setting AdjustmentsAttaching the LAT BAR or Nylon Strap to the Pulley Stations Tightening the Cables TROUBLE-SHOOTING and Maintenance3 2 Weight Resistance ChartResistance Cable Cable DiagramsWeight Stack Low Cable High CableRound Inner Cap R0102A Part Identification CHART-WESY19611Page Key No. Qty Description Part LIST-Model No. WESY19611Exploded DRAWING-Model Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT