Weider WESY39311 Locate the Low Cable 23 and the bag labeled, Low Pulley 76. Attach the Pulley

Page 14

25. Locate the Low Cable (23) and the bag labeled

“LOW PULLEY.” Route the Low Cable under the

3 1/2” Low Pulley (76). Attach the Pulley and the

5/8” x 9/16” Spacer (7) to the Press Frame (17) with

a 3/8” x 3 3/4” Bolt (88), 3/8” Washer (9), and a 3/8”

Nylon Locknut (21). Be sure that the parts are ori-

ented as shown in the drawing, and that the end

of the Cable with the ball is on the indicated

side of the Press Frame, between the Pulley and

the crossbar.

25

76

Ball

2317

Crossbar

88

9

7

1776

21

26. Route the Low Cable (23) around a 3 1/2” Pulley

(15). Attach Pulley and a Cable Trap (66) to the

lower hole in the Front Upright (42) with a 3/8” x

3 3/4” Bolt (88), a 3/8” Washer (9), and a 3/8” Nylon

Locknut (21). See the inset drawing. Be sure that

the Cable Trap is turned to hold the Cable in

place and that the Cable is routed around the

Pulley as shown.

26

42

15 66 21

23

23 15

21

66

42

Inset shows view

from other side

27. Route the Low Cable (23) around a 3 1/2” Pulley

(15). Attach the Pulley and a Cable Trap (66) to the

upper hole in the Press Frame (17) with a 3/8” x

3 1/2” Bolt (16), a 3/8” Washer (9), and a 3/8” Nylon

Locknut (21). Be sure that the Cable Trap is

889

27

23

9

turned to hold the Cable in place and that the

Cable is routed around the Pulley as shown.

15

16

17

21 66

28.Route the Low Cable (23) around another 3 1/2” Pulley (15). Attach the Pulley and a Cable Trap (66) to the upper hole in the Front Upright (42) with a 3/8” x 3 3/4” Bolt (88), a 3/8” Washer (9), and a 3/8” Nylon Locknut (21). See the inset drawing. Be sure that the Cable Trap is turned to hold the Cable in place and that the Cable is routed around the Pulley as shown.

28

42

23

66 21

15

23 15

88

66

42

Inset shows view

from other side

9

88

14

Image 14
Contents Customer HOT Line QUESTIONS?Model No. WESY39311 Serial No Table of Contents Important Precautions Before YOU Begin Decal NoQuestions? AssemblyFollowing Tools not Included are Required for Assembly Nylon Locknuts yetLocknuts yet Do not tighten the Nylon Locknuts yetDo not tighten the 5/16 Nylon Locknuts 3 yet Tighten all 5/16 Nylon Locknuts 3 used in stepsHoles in the Weight Guides are at the top, as Shown On the Weight Tube is sitting in the pin grooves Top WeightWeight Guides are at the top, as shown Locate and open the parts bag labeled ARM Assembly Nylon Locknut the Leg Press Arm must be able to pivot freelyNylon Locknut yet Cable Assembly Locknut the Pulley Bracket must be able to move freely Page 2 Low Pulley 76. Attach the Pulley Locate the Low Cable 23 and the bag labeledLOW PULLEY. Route the Low Cable under X 9/16 Spacer 7 to the Press Frame 17 withPage Cable Trap is positioned to hold the Cable in place Page Seat Assembly Locate and open the parts bag labeled Seat AssemblyPage Page Adjustments Changing the Weight SettingAttaching the LEG Lever to the LOW Pulley Station Adjusting the LEG Press PlateAttaching and Removing the Seat Weight Resistance Chart PlatesTROUBLE-SHOOTING and Maintenance Tightening the CablesTOP View Cable DiagramsHigh Cable 58 and Low Cable High CableMilitary Press Cable 72 and Leg Press Cable Leg Press CablePage Exploded DRAWING-Model No. WESY39311 Page Page Part LIST-Model No. WESY39311 Exploded Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty