Weider WESY39311 user manual Attaching and Removing the Seat, Adjusting the LEG Press Plate

Page 22

ATTACHING AND REMOVING THE SEAT

To attach the Seat (13), set the bracket on the Front Seat Frame (36) onto the indicated pin on the Front Upright (42). Attach the Front Seat Frame to the Front Upright with the 5/16” x 2 3/4” Carriage Bolt (14), 5/16” Washer (8) and the Seat Knob (40).

For some exercises, the Seat (13) must be removed. First, be sure that the chain is not attached to the leg lever. Next, remove the Seat Knob (40), 5/16” Washer

(8)and the 5/16” x 2 3/4” Carriage Bolt (14) from the Front Seat Frame (36). Lift the Front Seat Frame off the Front Upright (42).

ATTACHING THE LEG LEVER TO THE LOW PULLEY STATION

To use the Leg Lever (29), the seat must be attached to the front upright (see ATTACHING AND REMOV- ING THE SEAT above).

Attach one end of the Chain (52) to the Low Cable

(23)with a Cable Clip (53). Attach the other end of the Chain to the 5/16” x 2” Eyebolt (35) with a Cable Clip.

ADJUSTING THE LEG PRESS PLATE

Remove the Press Pin (97) from the Leg Press Plate (95) and the Leg Press Arm (96).

Align the welded tubes on the Leg Press Plate (95) with the desired set of holes in the Leg Press Arm (96). Re-insert the Press Pin (97) through the welded tubes on Leg Press Plate and the holes in the Leg Press Arm.

8

40

 

 

 

36

 

 

 

 

 

13

14

 

 

 

42

 

 

 

Pin

 

 

 

 

53

52

29

 

 

 

 

35

 

 

 

 

53

 

 

23

 

 

 

Welded

 

 

95

Tube

 

 

 

 

 

 

97

96

 

 

 

22

Image 22
Contents Model No. WESY39311 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Before YOU Begin Decal NoQuestions? AssemblyFollowing Tools not Included are Required for Assembly Nylon Locknuts yetLocknuts yet Do not tighten the Nylon Locknuts yetDo not tighten the 5/16 Nylon Locknuts 3 yet Tighten all 5/16 Nylon Locknuts 3 used in stepsWeight Guides are at the top, as shown On the Weight Tube is sitting in the pin grooves Top WeightHoles in the Weight Guides are at the top, as Shown Locate and open the parts bag labeled ARM Assembly Nylon Locknut the Leg Press Arm must be able to pivot freelyNylon Locknut yet Cable Assembly Locknut the Pulley Bracket must be able to move freely Page 2 Low Pulley 76. Attach the Pulley Locate the Low Cable 23 and the bag labeledLOW PULLEY. Route the Low Cable under X 9/16 Spacer 7 to the Press Frame 17 withPage Cable Trap is positioned to hold the Cable in place Page Seat Assembly Locate and open the parts bag labeled Seat AssemblyPage Page Adjustments Changing the Weight SettingAttaching and Removing the Seat Adjusting the LEG Press PlateAttaching the LEG Lever to the LOW Pulley Station Weight Resistance Chart PlatesTROUBLE-SHOOTING and Maintenance Tightening the CablesTOP View Cable DiagramsHigh Cable 58 and Low Cable High CableMilitary Press Cable 72 and Leg Press Cable Leg Press CablePage Exploded DRAWING-Model No. WESY39311 Page Page Part LIST-Model No. WESY39311 Exploded Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT