Weider WESY49201 TROUBLE-SHOOTING and Maintenance, Tightening the Cables, Be tightened, 23 or

Page 25

TROUBLE-SHOOTING AND MAINTENANCE

Make sure all parts are properly tightened each time you use the weight system. Replace any worn parts immedi- ately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.

TIGHTENING THE CABLES

Woven cable, the type of cable used on the weight system, can stretch slightly when it is first used. If there is slack in the cables before resistance is felt, the cables should be tightened. If any slack is felt when using the

front weight stack, both the High Cable (58) and the Low Cable (23) will need to be tightened. If any slack is felt when using the rear weight stack, both the Military Press Cable (72) and the Leg Press Cable (99) will need to

be tightened.

To tighten the cables, insert the weight pin into the middle of the weight stack. Slack can be removed from these cables several ways:

•See drawing 1. Tighten the 1/4” Nylon Locknut (2) that connects the end of the Low Cable (23) to the Long “U”- Bracket (57).

The Leg Press Cable (99) can be tightened in the same manner.

•See drawing 1. Move the 3 1/2” Pulley (15) to the other hole in one of the Long “U”-Brackets (57). Remove the

3/8” Nylon Locknut (21) and the 3/8” x 2” Bolt (12) from the Cable Trap (66), Pulley, and Long “U”-Bracket. Re-

attach the Pulley and Cable Trap. Be sure that the Cable Trap is in the proper position and that the Cable and Pulley move smoothly.

•See drawing 2. Tighten the 1/4” Nylon Locknut (2) that connects the end of the High Cable (58) to the Small “U”- Bracket (71).

The Military Press Cable (72) can be tightened in the same manner.

•See Drawing 3. If additional slack is felt while using the Leg Press Arm (96), then the end of the Leg Press Cable

(99)must be moved to the next hole in the Rear Seat

Frame (100). Remove the 5/16” x 2 3/4” Bolt (11), the 5/16” Washer (8), the end of the Cable, and both 5/16” Nylon Jamnuts (93) from the Rear Seat Frame. Re-attach

the Bolt, the Washer, the end of the Cable, and both Nylon Jamnuts to the next hole in the Rear Seat Frame.

Do not overtighten the cables; the top weight will be lift- ed off the weight stack.

1

 

66

15

 

21

 

57

12

 

2

 

 

23 or 99

2

 

72

58

 

71

 

2

 

71

 

 

2

3

 

11

96

 

8

 

 

100

 

99

 

93

 

93

If a cable tends to slip off the pulleys often, it may have become twisted. Remove the cable and re-install it.

If the cables need to be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents QUESTIONS? Table of ContentsAlways stand on the foot plate when per Important PrecautionsDecals shown below have been placed Before YOU Begin Frame Assembly AssemblyFollowing Tools not Included are Required for Assembly Frame AssemblyPress a 1 Square Inner Cap 6 into Front Upright Do not tightenOn the Top Frame. Press two 1 Inner Caps Each stack of Weights100 Bracket GroovesStack of Weights 25. Insert both Long WeightHoles 108ARM Assembly Frame Assembly ARM AssemblyDo not over Do not tighten the Nylon Locknut yet Must also be below the welded bracket on See the inset drawingAssist Upright Locate the High Cable 58. Wrap the High ARM Assembly Cable AssemblyCable in place Be sure thatDo not overtighten PlaceAttached parts BledOriented as shown That the Cable is between Locate the Low CableFrame ShownShown in the inset drawing Locknut 2 and a 1/4 WasherLocate the Military Press Cable A 1/4 Washer8 x 4 1/2 Bolt 112, a 3/8 Washer That the Cable and Pulley move smoothlyA 3/8 Nylon Locknut Around the Pulley as shownAssembled Cable in place See inset drawing aSee inset drawing B PivotLocate the Leg Press Cable Assembly4 Washer Indicated side. Note The three holes are forAttach one end of a Seat 13 to the Rear Seat AssemblyAttach the Assist Seat 104 and the Angle 104 110 105 114Washer 10 onto the Carriage Bolt ScrewsFront Seat Frame 36 with a 1/4 Washer A 1/4 x 2 Machine ScrewPress two 3/4 Round Inner Caps 34 into each Pad Tube On the followingChanging the Weight Setting AdjustmentsAttaching the LAT BAR or Nylon Strap to High Pulley Station Attaching the LAT BAR or Nylon Strap to LOW Pulley StationAttaching and Removing the Seat Adjusting the LEG Press PlateAttaching the LEG Lever to the LOW Pulley Station Press ArmLbs Weight Resistance ChartLbs Top 123 104 171 132 111 155 115 219 117 154 110 131 191 387 232 218 440 256 246 455 293Tightening the Cables TROUBLE-SHOOTING and MaintenanceBe tightened Must be moved to the next hole in the Rear SeatDo not touch or bind the cables High Cable 58 and Low Cable Cable DiagramsBe sure that the cable traps Low CableRear Seat Frame Military Press Cable 72 and Leg Press CableLeg Press Cable Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT Part No R0602AShipping purposes. If you cannot find a part in the parts Part from the Part List in the center of this manualIt has been pre-assembled StageR0602A Part Identification CHART-Model No. WESY49201Pulley 50 Not shown to scale 2 Pulley 15 Not shown to scale Round Inner Cap X 9/16 Spacer Round Cover Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty Description Part LIST-Model No. WESY49201Exploded DRAWING-Model No. WESY49201

WESY49201 specifications

The Weider WESY49201 is a versatile home gym system designed to help fitness enthusiasts achieve their workout goals without leaving the comfort of their homes. This multi-station weight system is particularly favored for its balance of functionality, durability, and compact design, catering to a wide range of exercises and fitness levels.

One of the primary features of the WESY49201 is its adjustable seat and backrest, which enhance user comfort and support during workouts. This feature is crucial for ensuring proper form and reducing the risk of injury. The equipment also comes with an extensive range of resistance options, allowing users to customize their workouts according to their individual strength levels and fitness objectives. This customization is facilitated by the inclusion of a weight stack system that provides effective resistance during various exercises.

The Weider WESY49201 is equipped with a number of workout stations, including a chest press, leg extension, and lat pulldown, each designed to target specific muscle groups. This multifunctionality allows users to perform a comprehensive workout routine targeting both upper and lower body muscles without requiring multiple pieces of equipment. Additionally, the integrated pull-up bar and preacher curl pad further expand the training possibilities.

Another notable characteristic of this home gym is its compact footprint, making it an ideal solution for individuals with limited space. Despite its smaller size, the WESY49201 does not compromise on stability or sturdiness, thanks to its heavy-duty steel construction. This durability ensures that users can rely on the equipment for a long time, even with regular use.

The assembly of the Weider WESY49201 is relatively straightforward, and the product comes with detailed instructions to aid users in setting it up efficiently. This feature, combined with its sturdy design, ensures that it remains stable during intense workouts.

In summary, the Weider WESY49201 stands out as a comprehensive solution for home fitness enthusiasts looking to build strength and improve overall fitness. With its variety of workout stations, user-friendly design, and ability to cater to multiple fitness levels, it serves as an excellent addition to any home gym, enabling users to perform a wide range of exercises while promoting health and wellness.
Top Page Image Contents