Weider WESY38322 user manual Frame Assembly, Locknut the Squat Knee Rest must be able to pivot

Page 6

1.

FRAME ASSEMBLY

Make sure that you understand all of the information on page 5 before you begin assembling the weight system.

1

 

 

 

71

85

 

 

110

 

120

86

 

 

 

Locate and open the parts bags labeled “FRAME ASSEMBLY 1” and “FRAME ASSEMBLY 2.”

Press a 2” Square Inner Cap (105) into the open end of the Long Base (120).

Insert eight 5/16” x 2 1/2” Carriage Bolts (110) up through the Long Base (120) and the Short Base (2) as shown. Note: It may be helpful to place tape over the heads of the Carriage Bolts to hold them in place.

Attach the Short Base (2) to the Long Base (120) with two 5/16” x 2 3/4” Bolts (85), the Long Frame Plate (71), and two 5/16” Nylon Locknuts (86). Do not tighten the Nylon Locknuts yet.

2.Attach the Outer Cap (24) to the Short Base (2) with two #8 x 3/4” Screws (98).

Press two 2” x 3” Inner Caps (58) into the Foot Plate (53). Attach the Foot Plate to the Long Base

(120)with two 5/16” x 2 1/2” Carriage Bolts (110) and two 5/16” Nylon Locknuts (86).

3.Attach the tether on the Pin (112) to the Long Base

(120)with a #10 x 1” Screw (14).

Attach the four Knee Rest Bumpers (123) to the Squat Knee Rest (41) with four #10 x 1” Screws (14). Attach the Squat Knee Rest to the Long Base

(120)with a 3/8” x 3 1/4” Bolt (96) and a 3/8” Nylon Locknut (87). Do not overtighten the Nylon

Locknut; the Squat Knee Rest must be able to pivot.

6

 

2

 

 

 

 

 

 

86

 

 

 

 

 

110

 

 

 

 

110

 

 

110

105

 

 

 

 

 

2

110

53

 

 

 

 

 

 

 

 

 

 

 

58

 

 

 

 

 

86

 

 

 

 

 

 

120

 

58

86

 

 

 

 

 

 

 

 

 

 

 

2

 

 

 

24

 

 

 

 

 

 

98

 

 

 

3

 

 

 

 

 

 

 

14

112

41

 

 

 

 

96

123

 

 

 

 

 

 

 

120

 

 

 

 

 

87

 

 

14

 

 

 

 

 

 

 

123

 

123

 

 

 

 

 

 

 

 

 

14

 

 

Image 6
Contents QUESTIONS? Model No. WESY38322 Serial NoCustomer HOT Line Table of Contents Important Precautions DecalBefore YOU Begin DecalOne on each side Assembly Frame Assembly Locknut the Squat Knee Rest must be able to pivotLocknuts yet Do not tighten the Nylon Locknuts yet110 120 That the Weight Tube is turned as shown Sure that the Weights are turned so the groovedSides of the Weights are facing downward Assemble the other weight stack in the same WayARM Assembly Open the parts bag labeled ARM AssemblyRepeat this step with the Left Butterfly Arm Repeat this step with the Right VKR Arm119 113 102 100 103 Page Page Page Page Page Assembly Locate and open the parts bag labeled SeatRepeat this step with the other end of the Squat Arm Tighten all of the 3/8 Nylon Locknuts 87 used in this step Converting the Butterfly Arms AdjustmentsChanging the Weight Setting Ing any exerciseAdjusting the Squat ARM, SEAT, or Butterfly Backrest Adjusting the Squat Knee RestAdjusting the Curl PAD Weight Resistance Chart PlatesTroubleshooting Tightening the CablesCable Diagrams Lat CableButterfly Cable Squat Cable VKR High Leg Lever VKR LowPart Identification CHART-Model No. WESY38322 R1102BX 3 1/4 Bolt Page Part LIST-Model No. WESY38322 Key Qty DescriptionExploded DRAWING-Model No. WESY38322 Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT