Use the operation buttons
Off
On: indicate the program about to run,or indicate the selected mode or indicate the water level
Flashing: indicate the running program
During sensing, it displays
During delay procedure, it displays the remained delay time (in hours).
During operation of programs,it displays the remaining time (in minutes).
In case of abnormal phenomenon, it displays the abnormal symbols (see to Page 15 ).
Push the “Power” button to switch on the power.
When the power is on, push it again to switch off the power.
Push the “Power” button to
switch on the power.If the “Start/Pause” button is not pushed, the washing machine will automatically switch off the power after 5 minutes.
After the power is switched on,press it to start the machine.
During working, push it to pause.
During pause, push this button to restart and go on working .
Memory 
Normal
Standard 
Strong
Wool 
Soft
Tub Dry 
Quick
Program
|
| Remaining | 47L | 52L | 1st Rinse |
| |
|
| Time | 38L | 43L |
| ||
|
|
|
|
| |||
|
|
|
|
|
|
| |
|
|
| 30L | 34L | 2nd Rinse |
| |
|
|
| 3rd Rinse |
| |||
|
| Delay Time | 22L | 26L | Power | ||
| Overflow |
|
| ||||
|
| 14L | 18L |
|
|
| |
|
|
| Water |
| Reserve |
|
|
|
|
| level |
| Water | Start/Pause | |
Wash | Rinse | Spin | Delay |
| |||
|
|
|
| ||||
During Memory,Strong,Soft,Normal and Standard | You can choose “Reserve Water” to keep water. | ||
program you can adjust the value of them. | It will keep the after rinsing water once finish rinsing | ||
For Wool you can select procedure , but can not | |||
in tub about 4 hours ,and buzzer every 15 minutes . | |||
change them. | |||
Press “Start/Pause” button or open and close the top | |||
|
| ||
|
| one time to collect the after rinsing water ,or else it | |
The digitron displays the time remained (in minutes) | will drain automatically,then go on for next program . | ||
| |||
before the washing is finished. |
| ||
Push the “Delay” button, the digitron displaysthe delay | The washing machine can detect the laundries | ||
time of washing (in hours).The indicator flashes to | automatically after detection, it will set the water | ||
indicate that the delay function is operating. | level to suitable value among level 26L,34L,43L, | ||
Push the “Delay” button to display the delay mode. | 52L automatically during the Normal,Memory | ||
|
| and Standard program. | |
Program | Applicable situation | You can also set water level by yourself.After the | |
machine is started, it will not set water level | |||
|
| ||
Normal | Washing the normal laundries | automatically. You shall push the “Start/Pause” | |
Strong | Washing the bigger and heavier laundries | button to make new setting. | |
If there’s water inside the tub, the machine can | |||
Soft | Washing the woollen textiles or underwear | not detect the laundries and will display water | |
level 34L .If wet laundries are put in, it may | |||
| Washing the laundries with small quantity | display water level 52L.You must set suitable | |
Quick | water level by yourself. | ||
and light soil | |||
| If Quick program is selected, it will display | ||
|
| ||
| The common wash, the washer will set to | water level 22L, the water level can be adjusted. | |
Memory | Custom program including wash, rinse, | If Tub Dry program is selected, the water level | |
| spin and water level automatically last time | will not respond. | |
| During operation of wash , rinse and soak | ||
Standard | Washing the normal laundries with less water | ||
program, you can push down the water level | |||
Wool | Washing the woollen textiles | button to add water. When you release the | |
button, or it reaches the overflow water level, | |||
| Drying the inner tub and the outer tub, | ||
Tub Dry | the machine will stop adding water. | ||
which can avoid growing mildew | The water level decided may be different from | ||
| |||
actual value because of the different moisture level of the laundries.
11