Polk Audio PA200.4 Features, Getting Started, Read this First, Safe Limits of Operation

Page 4

ENGLISH

Tools You May Need

ENGLISH

Loudspeakers can be damaged when an amplifier, regard-

WARNING

High-powered car audio systems may produce sound pressure levels that exceed the threshold at which hearing loss may result.

They may also impair a driver’s ability to hear traffic sounds or emergency vehicles. Use common sense and practice safe listening habits when listening to or adjusting your audio system.

FEATURES

Super-efficient Class D PWM design runs much cooler than conventional amps (PA1100.5 only).

High-speed MOSFET switching power supply and complementary bi-polar outputs

Stereo, mono, or simultaneous stereo/mono operation

Thermal, DC offset, reverse polarity, (short circuit and over/under voltage protection-PA500.4 and PA1100.5)

Selectable 12dB/octave two-way crossover (PA200.4)

Continuously variable 12dB/octave low-pass crossover (PA500.4 and PA1100.5)

Switchable subsonic filter 24dB/octave (PA500.4 and PA1100.5)

Switchable 8 dB bass EQ function.

Switchable 180° phase inversion (PA500.4 and PA1100.5)

Remote subwoofer level control function (PA500.4 and PA1100.5)

Variable input sensitivity optimizes match with different signal sources.

Chrome-plated wire terminals and RCA connectors ensure maximum signal transfer.

Rugged heatsink and cover.

Unity gain pass-through RCA jacks.

GETTING STARTED

Take Inventory

Check to ensure you have everything in your Polk Audio amplifier carton to start enjoying your system. Inside, you should find:

1.Polk Audio Amplifier

(either PA200.4, PA500.4 or PA1100.5)

2.Phillips Screws (4)

3.Mounting Washers (4)

4.Locking Washers (4)

5.Rubber Washers (4)

6.Fuse Replacements

7.Wire Harness

8.Owner’s Manual

9.Online Registration Card

10.Remote Volume Module - (PA500.4/PA1100.5 only)

11.Phone Line Cord - (PA500.4/PA1100.5 only)

Important Note: If anything is missing or damaged, or if your Polk Audio amplifier fails to operate, notify your dealer immediately. We recommend keeping your original carton and packing materials in case you need to ship the unit in the future.

In the event that your amplifier requires service or is ever stolen, you will need to have a record of the product’s serial number. Please take the time to enter that number in the space provided below. The serial number can be found on the bottom panel of the amplifier and on the amplifier packaging.

Serial Number:____________________________

Polk Audio Customer Service 800-377-7655

(M-F, 9-6 EST, US & Canada only) or via email polkcs@polkaudio.com. Outside the US & Canada, call 410-358-3600. To learn more about Polk Audio 12V amplifiers go to www.polkaudio.com Polk Audio, Inc. 5601 Metro Drive Baltimore, MD 21215

READ THIS FIRST

Installing a car audio system is a serious project. If you have any doubts about your ability to execute any of the installa- tion steps found in this manual, save yourself a lot of grief and contact a professional installer. Your Polk Audio dealer is a good place to find one. If you intend to do the installa- tion yourself we assume you possess some skill in the proper use of hand and power tools. No matter how much installa- tion experience you have, we recommend that you…

Read this manual thoroughly before you begin.

Plan your installation carefully.

Allow enough time to complete the installation without rushing.

Take steps to protect your car and upholstery from unwanted scratches and punctures.

Wear proper protective safety gear.

Phillips head screwdriver

Panel pry tool

Electric drill and 3/16" and 1/8" drill bits

Permanent ink marker or pencil

Solderless, crimp-on connectors and a crimping tool

Safety glasses

Wire strippers and cutters

Electrical tape

Grommets for passing wires through metal car walls

Amplifier Power Wire Kit (available at your authorized Polk Audio Dealer)

SAFE LIMITS OF OPERATION

Polk Audio specifies the recommended amplification range for each of its passive (non-amplified) loudspeakers. Typi-cally that specification will be expressed as a range of power such as 20-200 Watts (per channel). It is important to understand what those numbers mean when choosing

a receiver or amplifier for your Polk loudspeakers. The lower number indicates the lowest continuous rated power that will yield acceptable performance in a typical listening environment. The higher number indicates the highest

per channel power that should be used with your Polk speakers. That number should not be confused with a “Power Handling” specification and it does not imply that the speaker will safely handle that full amount of power on a long-term basis. We specify a wide range of power ratings because not all electronics manufacturers use the same method for rating power. In fact, high quality lower- rated amplifiers sound better and play louder than low quality units with higher power rating.

Automobile horsepower is good analogy. Your car probably has far more horsepower than it needs for your daily com- mute and is likely capable of going well over 120 MPH (190KM/hr). Having that extra power is good for on-ramp acceleration and danger avoidance (like getting away from brain-eating zombies) but that doesn’t mean that it is advis- able to operate your car on North American highways at full power and maximum speed for an extended period of time. Just ask your local state trooper if you are in doubt. Similarly, we recommend using amplifiers and receivers with rated power above the Power Handling limits of our speakers because having extra power available for short terms peaks is conducive to better sound quality, maximum dynamic range and effortless high volume output. But we strongly urge you not to use the full power of your amp or receiver for daily listening.

less of its wattage, is made to play at higher listening levels than its power can clearly produce. Operation at this level can result in very high levels of audible distortion originating in the amplifier, which can add a harsh, gritty sound to your listening material. If you hear distortion—turn the vol-

ume down or risk damaging your speakers. You can damage just about any speaker, regardless of power rating, if you drive an amplifier to or beyond the point of distortion.

INSTALLATION GUIDELINES

1.Please read this owner’s manual carefully before installing this amplifier.

2.Disconnect the battery ground terminal prior to making any electrical connections.

3.Check for any hazards or obstructions such as gas tanks, fuel or brake lines, and wiring harnesses before mounting the amplifier.

4.Pick a mounting location that will provide adequate access and ventilation and protect the amplifier from heat, moisture, and dirt.

5.To securely mount your amplifier you must first remove the top cover assembly. Unscrew the four (4) top cover assembly retaining screws.

6.Avoid sharp metal areas when routing cables to the amplifier, and run RCA cables away from the power cables and other potentially noisy car harnesses.

7.The amplifier should be grounded with a short, heavy gauge wire connected directly to the car at a bare metal surface, preferably scraped body sheet metal. Do not use factory ground locations, seat bolts, or brackets that are spot welded.

8.Always fuse your power connection within 8 to 10 inches of the battery terminal. Use a fuse or circuit breaker rated slightly more than the on-board fuse(s) of the amplifier(s). The gauge of power wire used should take into account the total current draw of the system, and the length of wire used. IASCA and other auto sound competition organizations have charts available for this; you can also find a chart in the MECP study guide. Minimum wire gauge recommendations for the individual ampli- fiers are listed on the specification page. Always use the same gauge wire for the amplifier ground that you use for the power wire. Be sure to examine the battery ground cable of the vehicle, and if necessary, upgrade

it by adding an additional ground wire that is the same gauge as the amplifier’s power wire. Remember, the amplifier can only deliver its rated output when it is not current limited by the power and ground supply wires.

9.This amplifier is designed to drive a speaker load that measures from 2 to 8 Ohms (1 Ohm on the PA1100.5 Sub Output). Keep in mind that heat is the long-term enemy of automotive electronics and the lower your

6 P A 1 2 V A M P L I F I E R S

 

W W W . P O L K A U D I O . C O M / A M P S 7

Image 4
Contents PA200.4 PA500.4 PA1100.5 English Polk Audio-A Passion for SoundFrançais Polk Audio-La passion du sonItaliano Espanol DeutschPortugues Features Installation GuidelinesGetting Started Read this FirstPhone Line Cord Remote Volume Module Remote PA500.4/PA1100.5RBridgedd g e d RBridgedd g e d Bridgedi d g e dInductor CapCap Right SubChannelH 1 F R 1O NFrontT Crossover Settings Gain AdjustmentChannelH 3 R E3ARear Channel 4 Rear Specifications LED Tube Installation OptionalCEA Specifications Guide D’INSTALLATION CaractéristiquesLire Attentivement Limites D’OPERATIONCordon téléphonique «REMOTE» PA500.4/PA1100.5Trois positions Arrière DroitCONNEXIONS-PANNEAU Arrière Opération stéréo-2 canaux vue du dessusRPontéi d g e d Pontéi d g e dCanauxH 1 F R1OAvantN T CCanauxH 4 R E4AArrièreRG e d Réglage DU Filtre Séparateur ET DU GainSpécifications CEA Installation DE Tubes DEL OptionnelSpécifications Espanol CaracterísticasInicio LEA Esto PrimeroMódulo de volumen a distancia Cordón de línea de teléfonoUn ventilador de enfriamiento externo De engarzarlasBEnr ipuented g d BEnr ipuented g d BEnr ipuented g e dBEnr ipuentedg d BEnr ipuented g d Sub U B Izquierdo CanaleDerecho Sub Izquierdo Canale TraseroR E a R3C HCanale3 R E ATraseroR Canale Trasero Canale DelanteroDelantero F R O N T Canale Especificaciones Especificaciones DE LA CEAInstallationsrichtlinien HöhepunkteLesen SIE Diesen Abschnitt Zuerst Sichere BetriebsgrenzwerteAbbildung 1-VERSTARKERANSCHLUSSE/REGLER-VORN PA200.4 Abbildung 1b Remote PA500.4/PA1100.5Abbildung 2-LED/LÜFTERKABELBAUM TelefonkabelAbbildung 4-LAUTSPRECHER-VERKABELUNGSDIAGRAMME PA200.4 LinksVorn HintenBrückenmodusr i d g e d KanalRechts Brückenmodusr i d g e dAbbildung 4-LAUTSPRECHER-VERKABELUNGSDIAGRAMME PA1100.5 Kanal Vorn3C KanalH 3 R EHintenA R Kanal Hinten Kanal C HDaten Linee Guida PER L’INSTALLAZIONE CaratteristichePER Iniziare DA Leggere SubitoCavo linea telefonica Modulo volume a distanza Ingresso subsonico/uscita di linea-SelezionaInterruttore modalità di ingresso-Seleziona il Interruttore uscita di linea PA1100.5Sinistra Canali Anteriore Right Channel SinistraCanali Posteriore Destra CanaliInduttore Canali InduttoreSinistra Canali Destra PosterioreR E a R SinistraC1HCanali1 F R OAnterioreN T Canali Anteriore Funzionamento Anteriore/PosterioreFunzionamento In Serie Anteriore/Posteriore Funzionamento Subsonico vista dall’altoInstallazione DI Tubi DI Luci LED Opzionali Regolazione Filtro Subsonico Solo PA1100.5Specifiche Specifiche CEAPrimeiros Passos LER PrimeiroLimites Seguros DE Operação Diretrizes DE InstalaçãoCabo de linha telefônica Canais FrontalDireito Canais EsquerdoEmr i dponteg d Indutor BonéIndutor Esquerdo Canais DireitoREmi dponteg d C1HCanais1 F R OFrontalN T Canais FrontalCanais Traseiro Emr i dponteg dEspecificações Instalação do Tubo DE LEDs OpcionalEspecificações DA CEA English About Polk Audio Français Polk AudioEspanol Acerca DE Polk Audio Deutsch Über Polk AudioLimited Warranty Garantie LimitéeA 1 2 V a M P L I F I E R S

PA200.4 specifications

The Polk Audio PA200.4 is an impressive amplifier designed to deliver powerful and high-quality sound for both novice and expert audio enthusiasts. This 4-channel amplifier is part of Polk's PA series and stands out due to its exceptional features and advanced technologies, making it a popular choice for those wishing to upgrade their car audio systems.

One of the main characteristics of the PA200.4 is its robust power output. The amplifier boasts 50 watts RMS per channel at 4 ohms, delivering an impressive 100 watts RMS at 2 ohms. This substantial power allows for loud, clear sound reproduction, perfect for driving high-performance speakers without distortion. The amplifier operates efficiently, providing consistent power even at lower volumes, ensuring that music remains rich and detailed across various listening levels.

The PA200.4 incorporates a range of technologies designed to enhance sound quality and improve user experience. The built-in high and low-pass filters allow for comprehensive tuning, enabling users to optimize the sound for their specific audio setup. The high-pass filter can be adjusted between 80 Hz and 120 Hz, while the low-pass filter also offers flexibility, catering to different types of speakers and subwoofers.

Another key feature of this amplifier is its impressive heat management system. Equipped with an advanced thermal management design, the PA200.4 is engineered to dissipate heat effectively, ensuring prolonged performance even during extended listening sessions. This is essential for maintaining sound quality and preventing damage to the components over time.

The PA200.4's construction is rugged and durable, featuring a compact chassis that makes installation straightforward in various vehicle models. Its lightweight design does not compromise its resilience and quality, making it a practical choice for those who may have limited space in their vehicle.

In summary, the Polk Audio PA200.4 is a versatile and powerful 4-channel amplifier that delivers superior sound quality with flexible tuning options. With its effective power output, advanced technologies, and solid construction, it is a compelling choice for anyone looking to enhance their car audio experience. Whether you are a seasoned audio enthusiast or just starting on your audio journey, the PA200.4 offers the features and performance to meet your needs.