Electrolux LAVAMAT 86810 manual Safety information concerning installation

Page 35

Installation and connection instructions

1Safety information concerning installation

•This washing machine cannot be built-in.

•Before using for the first time, check the appliance for damage sus- tained while it was being transported. Do not under any circumstanc- es connect an appliance that is damaged to the mains. In the event of damage to the appliance contact your supplier.

•Be sure to remove all the components of the transport lock before us- ing the appliance for the first time. Otherwise when spinning damage may be caused to the appliance or to neighbouring units or furniture.

•Before using the appliance for the first time, splash protection must be completed. (See “Removing transit packaging”).

•Always plug the mains plug into a correctly installed shockproof socket.

•If hard-wired: hard-wiring to the mains may only be carried out by an a qualified electrician.

•Prior to using the appliance for the first time, ensure that the rated voltage and current on the rating plate match the mains voltage and current where the appliance is to be installed. The required fuse pro- tection is also to be found on the rating plate.

•If work on the plumbing is required for the proper connection of the washing machine to the water supply, this must be undertaken by a registered plumber.

•If work on the electricity supply system is required for the proper connection of the washing machine to the electricity supply, this must be undertaken by a registered electrician.

•The washing machine’s mains cable must only be replaced by a Service Force Engineer

35

Image 35

Contents Lavamat Dear Customer Following symbols are used in the textContents Safety information concerning installation Installation and connection instructionsFollow the Installation and connection instructions SafetyPrior to using the appliance for the first time Child safetyResulting overheating may constitute a fire hazard General safetyCycle end at What is shown in the displayEasy Iron Program overviewUse/Features Care Symbols1 Programmende um Prior to using for the first timeN g u a g e R a c h ePreparing washing Setting the timePreparing and sorting washing Carrying out a wash programme prior to first useWashing powder/tablets for the main wash cycle Running a wash cycleAdding detergent/conditioner If you are using liquid detergent Switching on the appliance/selecting a programWith spin speed 0 the TEMP. RPM Options OK Time Changing spin speed/selecting rinse holdSpeed or Rinse Hold is displayed Current load display goes out if the door is closed Max . loadOpening the door/Loading the washing Sensitive Setting optionsPrewash, Sensitive, Stain, Night Cycle PrewashingSensitive Time Saving Short or Very Short Setting timesDelay Start Time savingStarting a programme Delay StartStart in 4h StartInterrupting a programme WashingProgramme progress Interrupting a programme/Adding washingIf Rinse Hold or Night Cycle was selected SetupWashing cycle complete/Removing the washing Memory 1, 2Changing the Memory Setting the MemoryMemory Store program Extra Rinse VolumeU n d N s e +Clock Set timeLanguage Each press of the key or if Desired setting. WithContrast and brightness Deactivating the child safety device Child safety deviceWashing drum Cleaning and maintenanceCleaning procedure Detergent dispenser drawerRemedying small malfunctions Clean the glass in the door and the rubber collar regularlyWhat to do if Door and rubber collarTap turned off Turn the tap on There are white residues on the washing If the wash result is not satisfactoryThere are grey stains on the washing Foam can still be seen following the final rinseCarrying out an emergency drain When the water has all drained awayDrain pump Old appliance DisposalPackaging material Consumption values Technical dataThis washing machine cannot be built-in Safety information concerning installationRemoving the transport lock Installing the applianceWhen using a sack trolley to transport the washing machine Transporting the applianceAppliance Where to installRemove both plastic caps sideways If the appliance is to stand on a base Making the appliance levelPermanent Connection Brown Live Wire coloured green and yellowElectrical Connection Permitted water pressure Connecting the appliance to the water supply35m long pressure hose is supplied with the appliance Water inletFor drainage into an outlet From your Service Force CentreWater Drainage Pumping heights of over 1 metre Great Britain Guarantee/Customer ServiceLU4 9QQ European GuaranteeMagyarország +36 Major Appliances 0870 5 929Customer Care For general enquiries concerning105 176 Subject to change without notice