Cub Cadet 59A40003727 manual Dismounting and mounting the loader, Dismounting the Loader, Falling

Page 15

section 9: dismounting and mounting the loader

Dismounting the Loader

• Continue raising the boom until center points of the support

 

plates on the bottom of the loader hitch bracket are resting

WARNING: A stored loader can fall and cause

on the ground, the loader hitch arms and bucket are support-

serious injury or death. Securely store loader and

ing the weight of the loader, and the bottom of the RH and

attachments on a hard level surface to prevent

LH masts have lifted off the tubular bars of the RH and LH

falling.

mounts. Refer to Figure 13.

 

• Stop the tractor engine and engage the parking brake.

WARNING: To provide necessary balance, the

• Disconnect the loader hoses from the tractor’s hydraulic

loader bucket must be installed before attaching

couplers by pushing inward the locking collar on each female

or detaching from tractor, or when loader is in

coupler of the tractor. Leave the hoses in the hose retainer

stored position.

rod.

IMPORTANT: The bucket must be installed to remove and

• Re-install the protective plugs in the tractor’s hydraulic cou-

re-mount the loader.

plers, and push the protective caps onto the male couplers of

Move the tractor and loader to a firm, level storage site.

the loader hoses.

• Re-start the tractor and carefully back the tractor away from

• Using the implement control lever, level the bucket and lower

the front loader.

it to the ground to take the weight off the mounting pins

• Re-install the mounting pins in the front mount receiver and

securing the loader hitch bracket in the front mount receiver.

Set the tractor’s parking brake.

secure with the two lynch pins.

• Remove the two lynch pins and withdraw the two mounting

WARNING: Do not climb or lean on the loader

pins that secure the loader hitch bracket in the front receiver.

while it’s in a stored position. Keep children and

Refer to Figure 13.

bystanders away from the stored loader.

• Carefully use the control lever to raise the boom and lower the

 

loader hitch bracket out of the front receiver.

 

LH Mast

Front Mount

Receiver

Mounting

Pin

LH Mount

Lynch Pin

Loader Hitch

Bracket

Center of

Support

Plate

Figure 13

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 769-03185 Operator’s ManualTable of Contents Finding Model NumberCalling Customer Support Training Safe operation practicesMove and turn tractor at low speeds Improper use of a loader can cause injury or deathMaintenance Labels found on loader Model 59A40003727 loader specifications To the Dealer If Using an Overhead Lift Unpacking the loaderIf an Overhead Lift is Not Available Install the RH and LH mounts as follows Initial InstallationInstalling the LH and RH Mounts Installing the Front Mount ReceiverFirst installation of Loader on Tractor Using an Overhead Lift For Initial InstallationFront Loader Preparation Mounting the Bucket #3-Blue Pre-Charging Cylinders for Initial InstallationHydraulic Out lets #2-YellowStart the tractor’s engine and operate at a low/safe RPM Initial Installation of Loader on TractorChecking Implement Control Lever Operation Stop the tractor engine and engage the parking brakeHose Retainer Rod LH Mast Front Mount Receiver Mounting Pin LH Mount Lynch PinStored position Dismounting and mounting the loaderDismounting the Loader FallingMount the loader as follows Mounting the LoaderOperation Correct Not Correct Operating the LoaderLifting the Load Carrying the LoadDumping the Bucket Lowering the BucketLower Roll Back Operating with a Float Control Surface Material Peeling and ScrapingLoading from a Bank Backblading BackgradingLoading Low Trucks or Spreaders from a Pile Handling Objects BackfillingMaintenance General MaintenanceLubrication Daily Oil Leaks TroubleshootingJerky Operation Slow OperationPosition Control When LeverBucket or Boom Leaks Down from HoldParts list 710-0376
Top Page Image Contents