JVC RX-6510VBK manual Plug the power cord into an AC outlet, R6PSUM-3/AA15F

Page 11

Connecting the Power Cord

 

Putting Batteries in the Remote Control

Before plugging the receiver into an AC outlet, make sure that all

Before using the remote control, put two supplied batteries first.

connections have been made.

When using the remote control, aim the remote control directly at

 

the remote sensor on the receiver.

Plug the power cord into an AC outlet.

English

Keep the power cord away from the connecting cables and the antenna. The power cord may cause noise or screen interference. We recommend that you use a coaxial cable to connect the antenna, since it is well-shielded against interference.

Note:

The preset settings such as preset channels and sound adjustment may be erased in a few days in the following cases:

–When you unplug the power cord.

–When a power failure occurs.

CAUTIONS:

•Do not touch the power cord with wet hands.

•Do not pull on the power cord to unplug the cord. When unplugging the cord, always grasp the plug so as not to damage the cord.

1

2

R6P(SUM-3)/AA(15F)

3

1.On the back of the remote control, remove the battery cover.

2.Insert batteries. Make sure to match the polarity:

(+) to (+) and (–) to (–).

3.Replace the cover.

If the range or effectiveness of the remote control decreases, replace the batteries. Use two R6P(SUM-3)/AA(15F) type dry-cell batteries.

CAUTION:

Follow these precautions to avoid leaking or cracking cells:

•Place batteries in the remote control so they match the polarity:

(+) to (+) and (–) to (–).

•Use the correct type of batteries. Batteries that look similar may differ in voltage.

•Always replace both batteries at the same time.

•Do not expose batteries to heat or flame.

8

Page 10 Page 12
Image 11
Page 10 Page 12
Contents RX-6510VBK Mises en garde, précautions et indications diverses English Français Table of Contents Front Panel Remote ControlEx. When you press CD button Parts IdentificationGetting Started Before InstallationConnecting the FM and AM Antennas Checking the Supplied AccessoriesAM Antenna Connections Connecting the SpeakersBasic connecting procedure Connecting the front speakersAudio component connections Connecting Audio/Video ComponentsConnecting the rear and center speakers Analog connectionsIf your audio components have a Compu Link jack To audio inputVideo component connections CD recorderDigital TV DVD player Digital connectionsTo S-video input To composite video input DVD playerR6PSUM-3/AA15F Plug the power cord into an AC outletSelecting the Source to Play Turning the Power On and Off StandbyBasic Operations Selecting different sources for picture and sound Adjusting the VolumeListening only with headphones Selecting the Front SpeakersMuting the Sound Attenuating the Input SignalAdjusting the Tone Adjusting the Subwoofer Output LevelRecording a Source Basic SettingsAdjusting the Front Speaker Output Balance Setting the Subwoofer InformationTo select the delay time of the rear speaker output Setting the Speakers for the DSP ModesCenter Delay appears on Display Rear Delay appears on DisplayTo select the appropriate item About the compression level Crossover FRQ Crossover Frequency appears on the displayTo select the low frequency effect attenuator level Drange Comp Dynamic Range Compression appears on DisplaySelecting the Analog or Digital Input Mode Digital Input Digital in Terminal SettingPress ANALOG/DIGITAL to Storing the Basic Settings AdjustmentsUsing the Sleep Timer Change the input modeReceiving Radio Broadcasts Tuning in Stations ManuallyUsing Preset Tuning Selecting the FM Reception Mode Surround modes Using the DSP ModesWhat are the DSP Modes? Possible × Impossible Reproducing the Sound FieldDAP modes Early reflections Behind Direct soundsAvailable DSP Modes According to the Speaker Arrangement Adjusting the Surround Modes Level you want Press DSP Mode repeatedly untilAdjust the effect level Press Effect to select an effectDance CLUB, HALL, or Pavilion appears on Display Adjusting the DAP ModesDAP mode Live Club Adjust the rear speaker output levelsPress Surround ON/OFF To cancel the Dolby/DTS Surround modeTo cancel the DSP mode Activating the DSP ModesAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Press the play 3 button on the CD playerSound control section Amplifier Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerREW CD changer7/P Cassette deckPause Operating Video ComponentsPlay StopOperating Other Manufacturers’ Video Equipment Press and hold TV PowerEnter manufacturer’s code using buttons Release TV PowerRelease CATV/DBS Power If there are more than one code listed for your brand Release VCR PowerTry to operate your VCR by pressing VCR Power 04, 05 Release Audio PowerPlay JVC Denon Panasonic Philips PioneerProblem Possible Cause Solution TroubleshootingHarmonic distortion SpecificationsPer channel, min. RMS, driven into 8 Ω Hz to 20 kHz with no more than 0.8% totalGeneral FM tuner IHFAM tuner EN, FR 0301NHMMDWJEIN

RX-6510VBK specifications

The JVC RX-6510VBK is a dynamic and robust A/V receiver that caters to both audiophiles and casual listeners alike. This versatile piece of equipment combines advanced technology with user-friendly features, making it an excellent choice for home theater setups and music enthusiasts.

One of the standout characteristics of the RX-6510VBK is its power output. It delivers 100 watts per channel across five channels, ensuring that movies and music come alive with impressive clarity and depth. The receiver supports a range of speaker configurations, allowing users to optimize their sound experience based on their available space and preferences. The flexibility of setup means that whether you are using a simple stereo speaker system or a full surround sound setup, the RX-6510VBK can accommodate and enhance the experience.

In terms of connectivity, the RX-6510VBK is equipped with multiple HDMI inputs, allowing users to connect various devices such as Blu-ray players, gaming consoles, and streaming devices effortlessly. The support for 4K video pass-through ensures that users can enjoy their media in stunning high definition, future-proofing their home entertainment systems. Additionally, the receiver includes optical and coaxial digital audio inputs, ensuring compatibility with a wide range of devices.

A notable technology incorporated within the RX-6510VBK is JVC’s digital sound processing, which enhances audio playback and ensures a clear, immersive sound experience. The built-in equalizer provides various settings to tailor the audio output based on listener preferences or room characteristics. This personalization allows for a sound profile that ideally suits the environment and enhances listener enjoyment.

Further enhancing its usability is the intuitive remote control that simplifies operation from across the room. The on-screen display provides quick access to settings and adjustments, making navigation straightforward and user-friendly.

With its range of features, solid power output, and impressive connectivity options, the JVC RX-6510VBK stands out as a reliable and high-quality choice for anyone looking to elevate their audio-visual experience. Whether it’s for movie nights or music enjoyment, this receiver delivers performance and flexibility that meets the demands of modern home entertainment systems.
Top Page Image Contents