JVC RX-6510VBK manual Adjusting the Surround Modes

Page 25
DOLBY SURROUND
DOLBY SURROUND

Adjusting the Surround Modes

Once you have adjusted the Surround modes, the adjustment is memorized for each Surround mode.

Dolby and DTS Surround adjustments

Before you start, remember...

•Make sure that you have set the speaker information correctly (see page 13).

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 3 again.

•You cannot adjust the rear speaker output levels when you have set “REAR SPK” to “NO.” See page 13.

•You cannot adjust the center speaker output level when you have set “CENTER SPK” to “NO.” See page 13.

From the remote control:

1. Select and play a sound source.

• To enjoy Dolby Pro Logic, play back a software encoded with

Dolby Surround and labeled with mark.

•To enjoy Dolby Digital, play back a software encoded with Dolby Digital and labeled with D I G I T A L mark.

•To enjoy DTS Digital Surround, play back a software encoded

with DTS Digital Surround and labeled with mark.

2. Press SURROUND ON/OFF to

SURROUND

 

activate an appropriate Surround

ON/OFF

 

mode — PRO LOGIC, DOLBY

 

DIGITAL or DTS SURROUND.

 

When “PRO LOGIC” is selected, the PRO LOGIC indicator lights up on the display.

•Each time you press the button, the Surround mode turns on and off alternately.

3. Press SOUND.

SOUND

The 10 keys are activated for sound adjustments.

4. Press TEST to check the speaker

TEST

output balance.

4

 

“TEST TONE L” starts flashing on the

 

5.Adjust the speaker output levels.

•To adjust the center speaker level, press CENTER +/– (from +10 dB to –10 dB).

•To adjust the left rear speaker level, press REAR•L +/– (from +10 dB to –10 dB).

•To adjust the right rear speaker level, press REAR•R +/– (from +10 dB to –10 dB).

– CENTER+

 

ENTER

– REAR• L+

– REAR• R+

2

3

5

6

8

9

 

MENU

 

ENTER

 

 

6. Press TEST again to stop the test tone.

TEST

 

4

On the front panel:

You can also use the buttons on the front panel to adjust the Surround modes. However, no test tone is available when using the buttons on the front panel. So, make adjustments while listening to the sound of the source played back.

1. Select and play a sound source.

• To enjoy Dolby Pro Logic, play back a software encoded with

Dolby Surround and labeled with mark.

•To enjoy Dolby Digital, play back a software encoded with Dolby Digital and labeled with D I G I T A L mark.

•To enjoy DTS Digital Surround, play back a software encoded

with DTS Digital Surround and labeled with mark.

2. Press SURROUND ON/OFF to

SURROUND ON/OFF

activate an appropriate Surround

 

mode — PRO LOGIC, DOLBY

 

DIGITAL or DTS SURROUND.

 

When “PRO LOGIC” is selected, the PRO LOGIC indicator lights up on the display.

•Each time you press the button, the Surround mode turns on and off alternately.

English

 

display, and a test tone comes out of the

 

 

 

 

 

speakers in the following order:

 

 

 

 

 

 

TEST TONE L

 

TEST TONE C

 

TEST TONE R

 

 

(Left front speaker)

 

(Center speaker)

 

(Right front speaker)

 

 

TEST TONE LS

TEST TONE RS

 

 

(Left rear speaker)

 

(Right rear speaker)

 

 

Notes:

•You can adjust the speaker output levels without outputting the test tone.

•No test tone comes out of the center speaker when “CENTER SPK” is set to “NO” (see page 13).

•No test tone comes out of the rear speakers when “REAR SPK” is set to “NO” (see page 13).

3.Adjust the speaker output levels.

1)Press ADJUST repeatedly until one of the following indications appears on the display.

“CENTER LEVEL”:

To adjust the center speaker level. “REAR L LEVEL”:

To adjust the left rear speaker level. “REAR R LEVEL”:

To adjust the right rear speaker level.

2)Press CONTROL UP 5/DOWN °to adjust the selected speaker output level (from +10 dB to –10 dB).

3)Repeat 1) and 2) to adjust the other speaker output levels.

ADJUST SETTING

CONTROL

DOWN UP

22

Page 24 Page 26
Image 25
Page 24 Page 26
Contents RX-6510VBK Mises en garde, précautions et indications diverses English Français Table of Contents Ex. When you press CD button Remote ControlParts Identification Front PanelConnecting the FM and AM Antennas Before InstallationChecking the Supplied Accessories Getting StartedBasic connecting procedure Connecting the SpeakersConnecting the front speakers AM Antenna ConnectionsConnecting the rear and center speakers Connecting Audio/Video ComponentsAnalog connections Audio component connectionsVideo component connections To audio inputCD recorder If your audio components have a Compu Link jackTo S-video input To composite video input Digital connectionsDVD player Digital TV DVD playerR6PSUM-3/AA15F Plug the power cord into an AC outletBasic Operations Turning the Power On and Off StandbySelecting the Source to Play Listening only with headphones Adjusting the VolumeSelecting the Front Speakers Selecting different sources for picture and soundAdjusting the Tone Attenuating the Input SignalAdjusting the Subwoofer Output Level Muting the SoundAdjusting the Front Speaker Output Balance Basic SettingsSetting the Subwoofer Information Recording a SourceCenter Delay appears on Display Setting the Speakers for the DSP ModesRear Delay appears on Display To select the delay time of the rear speaker outputTo select the low frequency effect attenuator level Crossover FRQ Crossover Frequency appears on the displayDrange Comp Dynamic Range Compression appears on Display To select the appropriate item About the compression levelSelecting the Analog or Digital Input Mode Digital Input Digital in Terminal SettingUsing the Sleep Timer Storing the Basic Settings AdjustmentsChange the input mode Press ANALOG/DIGITAL toUsing Preset Tuning Tuning in Stations ManuallyReceiving Radio Broadcasts Selecting the FM Reception Mode What are the DSP Modes? Using the DSP ModesSurround modes DAP modes Reproducing the Sound FieldEarly reflections Behind Direct sounds Possible × ImpossibleAvailable DSP Modes According to the Speaker Arrangement Adjusting the Surround Modes Adjust the effect level Press DSP Mode repeatedly untilPress Effect to select an effect Level you wantDAP mode Live Club Adjusting the DAP ModesAdjust the rear speaker output levels Dance CLUB, HALL, or Pavilion appears on DisplayTo cancel the DSP mode To cancel the Dolby/DTS Surround modeActivating the DSP Modes Press Surround ON/OFFRemote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemPress the play 3 button on the CD player Automatic Source SelectionOperating Audio Components Operating JVC’s Audio/Video ComponentsTuner Sound control section Amplifier7/P CD changerCassette deck REWPlay Operating Video ComponentsStop PauseEnter manufacturer’s code using buttons Press and hold TV PowerRelease TV Power Operating Other Manufacturers’ Video EquipmentRelease CATV/DBS Power Try to operate your VCR by pressing VCR Power Release VCR PowerIf there are more than one code listed for your brand Play Release Audio PowerJVC Denon Panasonic Philips Pioneer 04, 05Problem Possible Cause Solution TroubleshootingPer channel, min. RMS, driven into 8 Ω SpecificationsHz to 20 kHz with no more than 0.8% total Harmonic distortionAM tuner FM tuner IHFGeneral EN, FR 0301NHMMDWJEIN

RX-6510VBK specifications

The JVC RX-6510VBK is a dynamic and robust A/V receiver that caters to both audiophiles and casual listeners alike. This versatile piece of equipment combines advanced technology with user-friendly features, making it an excellent choice for home theater setups and music enthusiasts.

One of the standout characteristics of the RX-6510VBK is its power output. It delivers 100 watts per channel across five channels, ensuring that movies and music come alive with impressive clarity and depth. The receiver supports a range of speaker configurations, allowing users to optimize their sound experience based on their available space and preferences. The flexibility of setup means that whether you are using a simple stereo speaker system or a full surround sound setup, the RX-6510VBK can accommodate and enhance the experience.

In terms of connectivity, the RX-6510VBK is equipped with multiple HDMI inputs, allowing users to connect various devices such as Blu-ray players, gaming consoles, and streaming devices effortlessly. The support for 4K video pass-through ensures that users can enjoy their media in stunning high definition, future-proofing their home entertainment systems. Additionally, the receiver includes optical and coaxial digital audio inputs, ensuring compatibility with a wide range of devices.

A notable technology incorporated within the RX-6510VBK is JVC’s digital sound processing, which enhances audio playback and ensures a clear, immersive sound experience. The built-in equalizer provides various settings to tailor the audio output based on listener preferences or room characteristics. This personalization allows for a sound profile that ideally suits the environment and enhances listener enjoyment.

Further enhancing its usability is the intuitive remote control that simplifies operation from across the room. The on-screen display provides quick access to settings and adjustments, making navigation straightforward and user-friendly.

With its range of features, solid power output, and impressive connectivity options, the JVC RX-6510VBK stands out as a reliable and high-quality choice for anyone looking to elevate their audio-visual experience. Whether it’s for movie nights or music enjoyment, this receiver delivers performance and flexibility that meets the demands of modern home entertainment systems.
Top Page Image Contents