JVC RX-6510VBK manual Muting the Sound, Attenuating the Input Signal, Reinforcing the Bass

Page 14

English

Muting the Sound

From the remote control ONLY:

Press MUTING to mute the sound

MUTING

through all speakers and headphones

 

connected.

 

“MUTING” appears on the display and the volume turns off (the volume level indicator goes off).

From the remote control:

Press BASS +/– or TREBLE +/– to adjust the bass or treble sound level (+10 dB to –10 dB).

Attenuating the Input Signal

−BASS +

−TREBLE+

To restore the sound, press MUTING again so that “OFF” appears on the display.

•Turning MASTER VOLUME on the front panel or pressing VOLUME +/– on the remote control also restores the sound.

When the input level of the playing source is too high, the sounds will be distorted. If this happens, you need to attenuate the input signal level to prevent the sound distortion.

Reinforcing the Bass

You can boost the bass level.

Press BASS BOOST on the front panel or on the remote control to select the bass boost function.

BASS BOOSTBASSBOOST

On the front panel ONLY:

Press and hold INPUT ATT so that the INPUT ATT indicator lights up on the display.

•Each time you press and hold the button, the Input Attenuator mode turns on (“INPUT ATT ON”) or off (“INPUT NORMAL”).

INPUT

ANALOG/DIGITAL

INPUT ATT

On the front panel

On the remote

 

control

• Each time you press the button, the bass boost function turns on (“BASSBOOST ON”) and off (“BASSBOOST OFF”).

–Select “BASSBOOST ON” to activate the bass boost function. The BASS BOOST indicator lights up on the display.

–Select “BASSBOOST OFF” to cancel it.

The indicator goes off.

Note:

This function affects the front speaker sounds only.

Adjusting the Tone

You can adjust the bass and treble sounds as you like.

Before you start, remember....

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel:

1. Press ADJUST repeatedly until

ADJUST SETTING

 

“BASS” or “TREBLE” appears on

 

the display.

 

•Select “BASS” to adjust the bass sound level.

•Select “TREBLE” to adjust the treble sound level.

2. Press CONTROL UP 5/DOWN ° CONTROL

DOWN UP

to adjust the bass or treble sound level (+10 dB to –10 dB).

•Each time you press the button, the sound level changes by ± 2 steps.

Notes:

•This function is available only for the sources connected using the analog terminals.

•This function takes effect when the DSP mode is in use.

Adjusting the Subwoofer Output Level

You can adjust the subwoofer output level if you have selected “YES” for the “SUBWOOFER” (see page 12).

Once it has been adjusted, the receiver memorizes the adjustment.

Before you start, remember....

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

•When the front speakers are all deactivated, the subwoofer level cannot be adjusted.

On the front panel:

1.

Press ADJUST repeatedly until

ADJUST

SETTING

 

 

 

“SUBWFR LEVEL” appears on

 

 

 

the display.

 

 

 

The display changes to show the current setting.

 

 

2.

Press CONTROL UP 5/DOWN °

CONTROL

 

DOWN UP

 

 

to adjust the subwoofer output

 

 

 

level (+10 dB to –10 dB).

 

 

From the remote control:

 

 

1.

Press SOUND.

SOUND

 

 

 

 

The 10 keys are activated for sound adjustments.

 

2.

Press SUBWOOFER +/– to adjust

–SUBWOOFER+

 

the subwoofer output level (+10 dB

0

+10

 

FMMODE

100+

to –10 dB).

11

Page 13 Page 15
Image 14
Page 13 Page 15
Contents RX-6510VBK Mises en garde, précautions et indications diverses English Français Table of Contents Parts Identification Remote ControlEx. When you press CD button Front PanelChecking the Supplied Accessories Before InstallationConnecting the FM and AM Antennas Getting StartedConnecting the front speakers Connecting the SpeakersBasic connecting procedure AM Antenna ConnectionsAnalog connections Connecting Audio/Video ComponentsConnecting the rear and center speakers Audio component connectionsCD recorder To audio inputVideo component connections If your audio components have a Compu Link jackDVD player Digital connectionsTo S-video input To composite video input Digital TV DVD playerPlug the power cord into an AC outlet R6PSUM-3/AA15FSelecting the Source to Play Turning the Power On and Off StandbyBasic Operations Selecting the Front Speakers Adjusting the VolumeListening only with headphones Selecting different sources for picture and soundAdjusting the Subwoofer Output Level Attenuating the Input SignalAdjusting the Tone Muting the SoundSetting the Subwoofer Information Basic SettingsAdjusting the Front Speaker Output Balance Recording a SourceRear Delay appears on Display Setting the Speakers for the DSP ModesCenter Delay appears on Display To select the delay time of the rear speaker outputDrange Comp Dynamic Range Compression appears on Display Crossover FRQ Crossover Frequency appears on the displayTo select the low frequency effect attenuator level To select the appropriate item About the compression levelDigital Input Digital in Terminal Setting Selecting the Analog or Digital Input ModeChange the input mode Storing the Basic Settings AdjustmentsUsing the Sleep Timer Press ANALOG/DIGITAL toReceiving Radio Broadcasts Tuning in Stations ManuallyUsing Preset Tuning Selecting the FM Reception Mode Surround modes Using the DSP ModesWhat are the DSP Modes? Early reflections Behind Direct sounds Reproducing the Sound FieldDAP modes Possible × ImpossibleAvailable DSP Modes According to the Speaker Arrangement Adjusting the Surround Modes Press Effect to select an effect Press DSP Mode repeatedly untilAdjust the effect level Level you wantAdjust the rear speaker output levels Adjusting the DAP ModesDAP mode Live Club Dance CLUB, HALL, or Pavilion appears on DisplayActivating the DSP Modes To cancel the Dolby/DTS Surround modeTo cancel the DSP mode Press Surround ON/OFFPress the play 3 button on the CD player Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionTuner Operating JVC’s Audio/Video ComponentsOperating Audio Components Sound control section AmplifierCassette deck CD changer7/P REWStop Operating Video ComponentsPlay PauseRelease TV Power Press and hold TV PowerEnter manufacturer’s code using buttons Operating Other Manufacturers’ Video EquipmentRelease CATV/DBS Power If there are more than one code listed for your brand Release VCR PowerTry to operate your VCR by pressing VCR Power JVC Denon Panasonic Philips Pioneer Release Audio PowerPlay 04, 05Troubleshooting Problem Possible Cause SolutionHz to 20 kHz with no more than 0.8% total SpecificationsPer channel, min. RMS, driven into 8 Ω Harmonic distortionGeneral FM tuner IHFAM tuner EN, FR 0301NHMMDWJEIN

RX-6510VBK specifications

The JVC RX-6510VBK is a dynamic and robust A/V receiver that caters to both audiophiles and casual listeners alike. This versatile piece of equipment combines advanced technology with user-friendly features, making it an excellent choice for home theater setups and music enthusiasts.

One of the standout characteristics of the RX-6510VBK is its power output. It delivers 100 watts per channel across five channels, ensuring that movies and music come alive with impressive clarity and depth. The receiver supports a range of speaker configurations, allowing users to optimize their sound experience based on their available space and preferences. The flexibility of setup means that whether you are using a simple stereo speaker system or a full surround sound setup, the RX-6510VBK can accommodate and enhance the experience.

In terms of connectivity, the RX-6510VBK is equipped with multiple HDMI inputs, allowing users to connect various devices such as Blu-ray players, gaming consoles, and streaming devices effortlessly. The support for 4K video pass-through ensures that users can enjoy their media in stunning high definition, future-proofing their home entertainment systems. Additionally, the receiver includes optical and coaxial digital audio inputs, ensuring compatibility with a wide range of devices.

A notable technology incorporated within the RX-6510VBK is JVC’s digital sound processing, which enhances audio playback and ensures a clear, immersive sound experience. The built-in equalizer provides various settings to tailor the audio output based on listener preferences or room characteristics. This personalization allows for a sound profile that ideally suits the environment and enhances listener enjoyment.

Further enhancing its usability is the intuitive remote control that simplifies operation from across the room. The on-screen display provides quick access to settings and adjustments, making navigation straightforward and user-friendly.

With its range of features, solid power output, and impressive connectivity options, the JVC RX-6510VBK stands out as a reliable and high-quality choice for anyone looking to elevate their audio-visual experience. Whether it’s for movie nights or music enjoyment, this receiver delivers performance and flexibility that meets the demands of modern home entertainment systems.
Top Page Image Contents