JVC RX-6510VBK manual Selecting the Front Speakers, Adjusting the Volume, On the front panel only

Page 13

Selecting different sources for picture and sound

You can watch picture from a video component while listening to sound from another component.

Press one of the audio source selecting buttons — CD, TAPE/CDR, FM/AM, TV SOUND (or TV SOUND on the remote control), while viewing the picture from a video component such as the VCR or DVD player, etc.

Note:

Once you have selected a video source, pictures of the selected source are sent to the TV until you select another video source.

Selecting the Front Speakers

On the front panel ONLY:

When you have connected two pairs of the front speakers, you can select which to use.

SPEAKERS ON/OFF

1

2

To use the speakers connected to the FRONT SPEAKERS 1

terminals, press SPEAKERS ON/OFF 1 so that the SPK 1 indicator lights up on the display. (Make sure that the SPK 2 is not on the display.)

To use the speakers connected to the FRONT SPEAKERS 2

English

Adjusting the Volume

On the front panel:

To increase the volume, turn MASTER

VOLUME clockwise.

To decrease the volume, turn it counterclockwise.

•When you turn MASTER VOLUME rapidly, the volume level also changes rapidly.

•When you turn MASTER VOLUME slowly, the volume level also changes slowly.

From the remote control:

To increase the volume, press VOLUME +. To decrease the volume, press VOLUME –.

MASTER VOLUME

+

VOLUME

−

terminals, press SPEAKERS ON/OFF 2 so that the SPK 2 indicator lights up on the display. (Make sure that the SPK 1 is not on the display.)

To use both sets of the speakers, press SPEAKERS ON/OFF 1 and 2 so that the SPK 1 and SPK 2 indicators light up on the display.

To use neither sets of the speakers, press SPEAKERS ON/OFF 1 and 2 so that the SPK 1 and SPK 2 indicators disappear from the display.

Notes:

•If you select any of the DSP modes while using both the speakers connected to the FRONT SPEAKERS 1 and 2 terminals, the speakers connected to the FRONT SPEAKERS 2 terminals are deactivated.

•While the DSP MODE is in use, you can only select either the speakers connected to the FRONT SPEAKERS 1 or 2 terminals.

CAUTION:

Always set the volume to the minimum before starting any source. If the volume is set at its high level, the sudden blast of sound energy can permanently damage your hearing and/or ruin your speakers.

Note:

The volume level can be adjusted within the range of “0” (minimum) to “80” (maximum).

Listening only with headphones

You must turn off both pairs of speakers when you listen with headphones.

1.Connect a pair of headphones to the PHONES jack on the front panel.

2.Press SPEAKERS ON/OFF 1 and SPEAKERS ON/OFF 2 so that neither the SPK 1 nor SPK 2 indicator appears on the display.

This cancels the DSP mode currently selected, and activates the HEADPHONE mode (see below).

•“HEADPHONE” appears and H. PHONE indicator lights up on the display.

HEADPHONE mode:

This mode can reproduce the LFE channel signals, mixing them with the front channel signals. So you will not miss the subwoofer sounds even if you listen to a source using the headphones.

Notes:

•While in the HEADPHONE mode, you cannot use any DSP modes (see page 19.)

•Activating the speaker cancels the HEADPHONE mode and turns on the DSP mode previously selected.

CAUTION:

Be sure to turn down the volume before connecting or putting on headphones, as high volume can damage both the headphones and your hearing.

10

Page 12 Page 14
Image 13
Page 12 Page 14
Contents RX-6510VBK Mises en garde, précautions et indications diverses English Français Table of Contents Ex. When you press CD button Remote ControlParts Identification Front PanelConnecting the FM and AM Antennas Before InstallationChecking the Supplied Accessories Getting StartedBasic connecting procedure Connecting the SpeakersConnecting the front speakers AM Antenna ConnectionsConnecting the rear and center speakers Connecting Audio/Video ComponentsAnalog connections Audio component connectionsVideo component connections To audio inputCD recorder If your audio components have a Compu Link jackTo S-video input To composite video input Digital connectionsDVD player Digital TV DVD playerR6PSUM-3/AA15F Plug the power cord into an AC outletBasic Operations Turning the Power On and Off StandbySelecting the Source to Play Listening only with headphones Adjusting the VolumeSelecting the Front Speakers Selecting different sources for picture and soundAdjusting the Tone Attenuating the Input SignalAdjusting the Subwoofer Output Level Muting the SoundAdjusting the Front Speaker Output Balance Basic SettingsSetting the Subwoofer Information Recording a SourceCenter Delay appears on Display Setting the Speakers for the DSP ModesRear Delay appears on Display To select the delay time of the rear speaker outputTo select the low frequency effect attenuator level Crossover FRQ Crossover Frequency appears on the displayDrange Comp Dynamic Range Compression appears on Display To select the appropriate item About the compression levelSelecting the Analog or Digital Input Mode Digital Input Digital in Terminal SettingUsing the Sleep Timer Storing the Basic Settings AdjustmentsChange the input mode Press ANALOG/DIGITAL toUsing Preset Tuning Tuning in Stations ManuallyReceiving Radio Broadcasts Selecting the FM Reception Mode What are the DSP Modes? Using the DSP ModesSurround modes DAP modes Reproducing the Sound FieldEarly reflections Behind Direct sounds Possible × ImpossibleAvailable DSP Modes According to the Speaker Arrangement Adjusting the Surround Modes Adjust the effect level Press DSP Mode repeatedly untilPress Effect to select an effect Level you wantDAP mode Live Club Adjusting the DAP ModesAdjust the rear speaker output levels Dance CLUB, HALL, or Pavilion appears on DisplayTo cancel the DSP mode To cancel the Dolby/DTS Surround modeActivating the DSP Modes Press Surround ON/OFFRemote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemPress the play 3 button on the CD player Automatic Source SelectionOperating Audio Components Operating JVC’s Audio/Video ComponentsTuner Sound control section Amplifier7/P CD changerCassette deck REWPlay Operating Video ComponentsStop PauseEnter manufacturer’s code using buttons Press and hold TV PowerRelease TV Power Operating Other Manufacturers’ Video EquipmentRelease CATV/DBS Power Try to operate your VCR by pressing VCR Power Release VCR PowerIf there are more than one code listed for your brand Play Release Audio PowerJVC Denon Panasonic Philips Pioneer 04, 05Problem Possible Cause Solution TroubleshootingPer channel, min. RMS, driven into 8 Ω SpecificationsHz to 20 kHz with no more than 0.8% total Harmonic distortionAM tuner FM tuner IHFGeneral EN, FR 0301NHMMDWJEIN

RX-6510VBK specifications

The JVC RX-6510VBK is a dynamic and robust A/V receiver that caters to both audiophiles and casual listeners alike. This versatile piece of equipment combines advanced technology with user-friendly features, making it an excellent choice for home theater setups and music enthusiasts.

One of the standout characteristics of the RX-6510VBK is its power output. It delivers 100 watts per channel across five channels, ensuring that movies and music come alive with impressive clarity and depth. The receiver supports a range of speaker configurations, allowing users to optimize their sound experience based on their available space and preferences. The flexibility of setup means that whether you are using a simple stereo speaker system or a full surround sound setup, the RX-6510VBK can accommodate and enhance the experience.

In terms of connectivity, the RX-6510VBK is equipped with multiple HDMI inputs, allowing users to connect various devices such as Blu-ray players, gaming consoles, and streaming devices effortlessly. The support for 4K video pass-through ensures that users can enjoy their media in stunning high definition, future-proofing their home entertainment systems. Additionally, the receiver includes optical and coaxial digital audio inputs, ensuring compatibility with a wide range of devices.

A notable technology incorporated within the RX-6510VBK is JVC’s digital sound processing, which enhances audio playback and ensures a clear, immersive sound experience. The built-in equalizer provides various settings to tailor the audio output based on listener preferences or room characteristics. This personalization allows for a sound profile that ideally suits the environment and enhances listener enjoyment.

Further enhancing its usability is the intuitive remote control that simplifies operation from across the room. The on-screen display provides quick access to settings and adjustments, making navigation straightforward and user-friendly.

With its range of features, solid power output, and impressive connectivity options, the JVC RX-6510VBK stands out as a reliable and high-quality choice for anyone looking to elevate their audio-visual experience. Whether it’s for movie nights or music enjoyment, this receiver delivers performance and flexibility that meets the demands of modern home entertainment systems.
Top Page Image Contents