JVC RX-6510VBK Press Effect to select an effect, Level you want, Press DSP Mode repeatedly until

Page 26

English

JVC Theater Surround adjustments

Before you start, remember...

• Make sure that you have set the speaker information correctly

(see page 13).

5.

Press TEST again to stop the test tone.

TEST

4

 

 

6.

Press EFFECT to select an effect

EFFECT

 

 

• There is a time limit in doing the following steps. If the setting is

level you want.

1

canceled before you finish, start from step 2 again.

• You cannot adjust the rear speaker output levels when you have set

“REAR SPK” to “NO.” See page 13.

• You cannot adjust the center speaker output level when you have

set “CENTER SPK” to “NO.” See page 13.

From the remote control:

1. Press DSP MODE repeatedly until

DSP

MODE

“THEATER” appears on the

 

display.

 

The PRO LOGIC and DSP indicators also light up on the display.

2. Press SOUND.

SOUND

 

The 10 keys are activated for sound adjustments.

3. Press TEST to check the speaker

TEST

output balance.

4

 

“TEST TONE L” starts flashing on the display, and a test tone comes out of the speakers in the following order:

•Each time you press the button, the effect level changes as follows:

DSP EFFECT 1 DSP EFFECT 2 DSP EFFECT 3

DSP EFFECT 5

DSP EFFECT 4

As the number increases, JVC Theater Surround becomes stronger (normally set it to “DSP EFFECT 3”).

On the front panel:

You can also use the buttons on the front panel to adjust the Surround modes. However, no test tone is available when using the buttons on the front panel. So, make adjustments while listening to the sound of the source played back.

1. Press DSP MODE repeatedly until

DSP MODE

 

“THEATER” appears on the

 

display.

 

The PRO LOGIC and DSP indicators also light up on the display.

 

TEST TONE L

 

TEST TONE C

 

TEST TONE R

 

 

(Left front speaker)

 

(Center speaker)

 

(Right front speaker)

 

 

TEST TONE LS

 

TEST TONE RS

 

 

(Left rear speaker)

 

(Right rear speaker)

 

 

Notes:

•You can adjust the speaker output levels without outputting the test tone.

•No test tone comes out of the center speaker when “CENTER SPK” is set to “NO” (see page 13).

•No test tone comes out of the rear speakers when “REAR SPK” is set to “NO” (see page 13).

4.Adjust the speaker output levels.

•To adjust the center speaker level, press CENTER +/– (from +10 dB to –10 dB).

•To adjust the left rear speaker level, press REAR•L +/– (from +10 dB to –10 dB).

•To adjust the right rear speaker level, press REAR•R +/– (from +10 dB to –10 dB).

– CENTER+

– REAR• L+

– REAR• R+

2

3

5

6

8

9

 

MENU

 

ENTER

 

 

2.Adjust the speaker output levels.

1)Press ADJUST repeatedly until one of the following indications appears on the display.

“CENTER LEVEL”:

To adjust the center speaker level. “REAR L LEVEL”:

To adjust the left rear speaker level. “REAR R LEVEL”:

To adjust the right rear speaker level.

2)Press CONTROL UP 5/DOWN °to adjust the selected speaker output level (from +10 dB to –10 dB).

3)Repeat 1) and 2) to adjust the other speaker output levels.

3.Adjust the effect level.

1)Press ADJUST repeatedly until “DSP EFFECT” appears on the display. The display changes to show the current setting.

2)Press CONTROL UP 5/DOWN °to select the effect level.

•Each time you press the button, the effect level changes as follows:

ADJUST SETTING

CONTROL

DOWN UP

ADJUST SETTING

CONTROL

DOWN UP

DSP EFFECT 1 DSP EFFECT 2 DSP EFFECT 3

DSP EFFECT 5

DSP EFFECT 4

As the number increases, JVC Theater Surround becomes stronger (normally set it to “DSP EFFECT 3”).

23

Page 25 Page 27
Image 26
Page 25 Page 27
Contents RX-6510VBK Mises en garde, précautions et indications diverses English Français Table of Contents Parts Identification Remote ControlEx. When you press CD button Front PanelChecking the Supplied Accessories Before InstallationConnecting the FM and AM Antennas Getting StartedConnecting the front speakers Connecting the SpeakersBasic connecting procedure AM Antenna ConnectionsAnalog connections Connecting Audio/Video ComponentsConnecting the rear and center speakers Audio component connectionsCD recorder To audio inputVideo component connections If your audio components have a Compu Link jackDVD player Digital connectionsTo S-video input To composite video input Digital TV DVD playerPlug the power cord into an AC outlet R6PSUM-3/AA15FSelecting the Source to Play Turning the Power On and Off StandbyBasic Operations Selecting the Front Speakers Adjusting the VolumeListening only with headphones Selecting different sources for picture and soundAdjusting the Subwoofer Output Level Attenuating the Input SignalAdjusting the Tone Muting the SoundSetting the Subwoofer Information Basic SettingsAdjusting the Front Speaker Output Balance Recording a SourceRear Delay appears on Display Setting the Speakers for the DSP ModesCenter Delay appears on Display To select the delay time of the rear speaker outputDrange Comp Dynamic Range Compression appears on Display Crossover FRQ Crossover Frequency appears on the displayTo select the low frequency effect attenuator level To select the appropriate item About the compression levelDigital Input Digital in Terminal Setting Selecting the Analog or Digital Input ModeChange the input mode Storing the Basic Settings AdjustmentsUsing the Sleep Timer Press ANALOG/DIGITAL toReceiving Radio Broadcasts Tuning in Stations ManuallyUsing Preset Tuning Selecting the FM Reception Mode Surround modes Using the DSP ModesWhat are the DSP Modes? Early reflections Behind Direct sounds Reproducing the Sound FieldDAP modes Possible × ImpossibleAvailable DSP Modes According to the Speaker Arrangement Adjusting the Surround Modes Press Effect to select an effect Press DSP Mode repeatedly untilAdjust the effect level Level you wantAdjust the rear speaker output levels Adjusting the DAP ModesDAP mode Live Club Dance CLUB, HALL, or Pavilion appears on DisplayActivating the DSP Modes To cancel the Dolby/DTS Surround modeTo cancel the DSP mode Press Surround ON/OFFPress the play 3 button on the CD player Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionTuner Operating JVC’s Audio/Video ComponentsOperating Audio Components Sound control section AmplifierCassette deck CD changer7/P REWStop Operating Video ComponentsPlay PauseRelease TV Power Press and hold TV PowerEnter manufacturer’s code using buttons Operating Other Manufacturers’ Video EquipmentRelease CATV/DBS Power If there are more than one code listed for your brand Release VCR PowerTry to operate your VCR by pressing VCR Power JVC Denon Panasonic Philips Pioneer Release Audio PowerPlay 04, 05Troubleshooting Problem Possible Cause SolutionHz to 20 kHz with no more than 0.8% total SpecificationsPer channel, min. RMS, driven into 8 Ω Harmonic distortionGeneral FM tuner IHFAM tuner EN, FR 0301NHMMDWJEIN

RX-6510VBK specifications

The JVC RX-6510VBK is a dynamic and robust A/V receiver that caters to both audiophiles and casual listeners alike. This versatile piece of equipment combines advanced technology with user-friendly features, making it an excellent choice for home theater setups and music enthusiasts.

One of the standout characteristics of the RX-6510VBK is its power output. It delivers 100 watts per channel across five channels, ensuring that movies and music come alive with impressive clarity and depth. The receiver supports a range of speaker configurations, allowing users to optimize their sound experience based on their available space and preferences. The flexibility of setup means that whether you are using a simple stereo speaker system or a full surround sound setup, the RX-6510VBK can accommodate and enhance the experience.

In terms of connectivity, the RX-6510VBK is equipped with multiple HDMI inputs, allowing users to connect various devices such as Blu-ray players, gaming consoles, and streaming devices effortlessly. The support for 4K video pass-through ensures that users can enjoy their media in stunning high definition, future-proofing their home entertainment systems. Additionally, the receiver includes optical and coaxial digital audio inputs, ensuring compatibility with a wide range of devices.

A notable technology incorporated within the RX-6510VBK is JVC’s digital sound processing, which enhances audio playback and ensures a clear, immersive sound experience. The built-in equalizer provides various settings to tailor the audio output based on listener preferences or room characteristics. This personalization allows for a sound profile that ideally suits the environment and enhances listener enjoyment.

Further enhancing its usability is the intuitive remote control that simplifies operation from across the room. The on-screen display provides quick access to settings and adjustments, making navigation straightforward and user-friendly.

With its range of features, solid power output, and impressive connectivity options, the JVC RX-6510VBK stands out as a reliable and high-quality choice for anyone looking to elevate their audio-visual experience. Whether it’s for movie nights or music enjoyment, this receiver delivers performance and flexibility that meets the demands of modern home entertainment systems.
Top Page Image Contents