Miele PW 6065 Plus manual Drainage, Drain valve, Drain pump

Page 53

Installation

Drainage

Drain valve

The machine is drained with a motorized drain valve. A connection can be made to an on-site floor drain (gully with an air gap) on an angle.

Drain pump

The wash water is drained using a pump with a 3 ft (1 m) delivery height. Make sure there are no kinks in the drain hose. The elbow on the end of the drain hose can be turned or removed if necessary.

Possible connections:

1.Directly into a sink: Hook the hose over the edge of the sink and secure it firmly (e.g. by tying the hose to the water faucet).

2.To a stand pipe: Place the drain hose into a 11/2" (4 cm) stand pipe and secure it firmly.

3.To a floor drain: The machine is equipped with an air gap/ anti-siphoning system so that no minimum drain height is required.

If necessary the drain hose can be extended up to 16' 5" (5 m). The hose extension can be purchased from your Miele dealer or Miele.

The drain pump must be replaced for drain heights over 3 ft (1 m). The maximum allowable drain height is 5 ft 11 in (1.8 m). A stronger pump for these heights can be purchased from your dealer or Miele.

53

Image 53
Contents Operating manual Washer PW 6065 Plus Contents Contents Use Technical SafetyImportant Safety Instructions Children Using accessoriesDescription of the machine Guide to the washerControl panel Program selection possibility Display functionMain menu Basic menu of a wash program Settings JMenu Program selection Before using for the first time General tips Using the washerSort the laundry Coin mechanism Load the washerSelect a program Too much detergent may cause Adding detergentToo little detergent may cause At the end of a program Starting a programSelecting/Changing a Favorite FavoritesBasic menu Select a programSelecting Extras Selecting a temperatureSelecting the spin speed Assigning a direct select button Saving a FavoriteOptions Accessing the sub-menu ExtrasPre-wash Starch StopWater plus Rinse StopIntensive Select the sub-menu Delay Start Delay StartSelect the Delay Start time Starting the Delay StartSpin speed SpinRinse spin Without final spinProgram guide Silk /30C to cold Woollens 40C to coldShirts 60C to cold Denim 104C to coldKitchen linen 95C to 60C Additional programsTable linen 60C to 30C Curtains 104C to coldProofing 104F to 86F Outerwear 40C to coldSluice 75C or Sluice 65C Disinfection programsHygiene Main wash Rinse Spin Program sequenceHigh Spin Special features in the program sequence Anti-creasePre-rinse OuterwearTo change a program To cancel a programTo change a program Adding/removing laundry during a wash programWater hardness DetergentWater softener Normal soilingDye removers / Fabric dyes Fabric softener, liquid starchCleaning the detergent drawer Cleaning and CareCleaning the washer Cleaning the filter in the inlet valve Cleaning the inlet hose filterCleaning the inlet hose filters Wash program cannot be started Frequently asked questionsGeneral problems with the washer Poor wash results Door will not open when the Door button is pressed Machines with a drain pump Remove the toolOpen the lint trap door Open the drum door Machines with a drain valve Changing the light bulb PC Update After sales serviceOptional accessories RepairsInstallation Instructions Front view InstallationRear view Reinstallation of the machine lid Installation on a baseWasher/ Dryer Stack Coin mechanismInstallation Installation siteRemoving the shipping struts Do not lift the washer by the drum doorPull out the shipping strut out Pull the shipping strut outInstalling the shipping struts Leveling the washer Water connection MaintenanceCold water connection Extension hosesHot water connection Drain pump DrainageDrain valve Electrical connection Technical Data Disposal of an old appliance Help to protect the environmentDisposal of the packing materials Menu Settings J To adjust standard settings Opening the menu Settings Settings JSelecting Settings Leaving the Settings menuSuds cooling Language JContrast Time of dayBrightness Selecting the clockNot in current prog. Factory default Temperature unitStandby MemoryEntering the code Menu Settings Supervisor levelMenu Settings Supervisor level Supervisor level Sort languagesIntensive Water plus SaveRinse water Auto load control Main wash waterPre-wash water Water level Min. iron Water level CottonsWash time Cottons Pre-wash temp. CotHygiene No. of programs DisinfectionSluice Pre-wash Kitchen linenNo. rinses Cottons Optimize energy Pre-rinse CottonsNo. rinses min. iron Pre-rinse Min. ironExternal dispenser Leaving the Settings menuNo detergent Page Page Alteration rights reserved