AEG 76730 manual Prepare the installation place, Installation on a concrete base

Page 44

Installation and connection instructions

Prepare the installation place

•The installation surface must be clean and dry, free of floor polish residues and other greasy coatings so that the unit does not slip away. Do not use lubricants as a sliding aid.

•Installation on a high-veil carpet or floor tiles with soft sponge backs is not recommended because the standing safety of the appliance is then no longer ensured.

•By installation surfaces with small-format tiles, lay a conventional rubber mat underneath.

•Minor unevenness of the floor surface should never be levelled out by laying pieces of wood, card or similar materials, but rather should al- ways be compensated for by adjusting the screw feet.

•If, for space reasons, it is not possible to avoid setting up the unit di- rectly next to a gas or coal-fired cooker: install a thermal insulation panel between the cooker and washing machine (85 x 57cm) which must have an aluminium film on the side against the cooker.

•The washing machine must not be set up in a room where there is a danger of frost. Frost hazard!

•Flexible feed and drain tubings may not be crinkled or squeezed.

Installation on a concrete base

If the unit is set up on a concrete base, for safety reasons it is essential to fit stand plates in which the washing ma- chine is adjusted. The stand plates are available from Customer Service under the spare parts number 645 425 058.

Installation on vibrating floors

Where the floor vibrates, particularly in the case of wooden beam floors with pliable boards, securely screw a water-resistant wooden panel at least 15mm thick onto at least 2 floor planks. If possible, set up the unit in the corner of a room, as the wooden floor is optimally re- strained there and is therefore least likely to be subject to resonance vi- brations.

44

Image 44

Contents ÖKO-LAVAMAT 76730 update Tips on using the appliance Dear CustomerPlease read this user information carefully Pass it on to any future owners of the unitContents What to do if Program TablesWarranty conditions / Customer service centres Correct Use SafetyBefore Using for the First Time Safety of Children and Infirm Persons General SafetyDisposing of your old appliance DisposalDisposing of the Packaging Material Environmental tips Drawer for detergent and care agent Unit descriptionFront view Control panel Program SelectorMain washing cycle for delicates at 30 C or 40 C WOOL/P HandwashHandwash Is added, spinCome effective at higher temperatures Additional Program ButtonsWarm pre wash before the main washing cycle Shorter washing cycle for slightly dirty washingWhat does Update mean? Consumption ValuesWater Protection Aqua Control Filling Quantity Water EnergySort washing and prepare Before the First WashPrepare washing cycle Washing Types and Care Codes Water hardness details How much washing detergent and care agent?Water softener After the Washing Program Ends Run a Washing CycleBrief Instructions Setting the Washing Program TablesSelecting the rinse hold function Changing the spin speed/Selecting the rinse hold functionChanging the spin speed Soaking Duration Set the Delay Timer/Soaking DurationDelay Timer Opening and Closing the Filling Door Add the washingFor the maximum filling quantities, see the Program tables Close the filling door securelyIf using liquid detergent / tablets Add Washing Detergent/Care AgentCompartment for pre-wash agent/soaking agent Or for water softenerIf the time preselection is set Start the Washing ProgramIs pressed Multi-display Completion of the Washing ProgramProgram sequence display Changing a Washing Program Changing or aborting a programSelect the Additional Program Change the Spin SpeedIf the power supply is interrupted Washing Cycle Ended/Remove WashingCare Codes Temperature Program TablesWashing Type of Washing MaxSeparate Conditioning/Starching/Impregnating Separate RinseSeparate Spin Type of WashingCleaning and Care Detergent DrawerWashing Drum Main doorWhat to do if Remedying FaultsProblem Possible Cause Remedy Water tap is closed Open the water tap No water runs Tighten the intake hose Head 1m from units floor If the washing results are not satisfactory If there are still grey spots on the washingIf at the end of the last rinse foam is still visible If there are white remnants on the washingCarrying out emergency drainage When the water is completely drained Before cleaning the drain pumpDrain pump Ing pumped out, e.g. if the pump is blockedNo additional rinse is set when the unit is delivered Cancel Additional RinseAdditional Rinse RINSE+ To rinse with more waterCancelling the child safety Feature Child Safety FeatureSetting the child safety feature Installation and connection instructions Installation Safety PrecautionsInstallation of the appliance When transporting the unit with a sack trolleyTransporting the appliance Remove transport packagingAre supplied with it Cover the hole with the cap CInstallation on vibrating floors Prepare the installation placeInstallation on a concrete base Compensate for floor unevenness Permissible water pressure Electrical connectionWater connection Water inflow Water drain Delivery heads over 1mWater drain-off inside a siphon Water drain-off inside a basinTechnical data DimensionsDimensions in mm = 0.1 1.0 MpaFurther after-sales service agencies overseas Autres agences étrangères assurant le service après-venteWeitere Kundendienststellen im Ausland Otros puntos de Postventa en el extranjeroAustralia Korea South Namibia Croatia New ZealandBulgaria Kuwait/Arabian Gulf Cyprus Lebanon OmanIsrael Malaysia Saudi Arabia Japan Singapore SloveniaThailand Slovakia Rep South Africa HungaryPage Index Service When do you incur costs even during the warranty period?AEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG

Related manuals

Manual 56 pages 44.61 Kb