Whirlpool GHW9200L, GHW9100L manual

Page 16

10.When the washer is level, use a 9/16” open-end wrench to securely tighten all four (4) feet locknuts against the pedestal. (Fig. 2-7)The locknuts must be tightened.

Fig. 2-7

11.Pull both drawer slides out and reas- semble the drawer to the drawer slides with the two (2) Phillips head screws. (Fig. 2-8)Use of the two (2) dividers is optional. Close the drawer.

Fig. 2-8

2 - 8

Image 16
Contents Front-Loading Automatic Washer Model Numbers Forward Goal and ObjectivesTable of Contents Page Important Safety Information GeneralWhirlpool Model & Serial Number Designators Model Number G H W 9100 L WSpecifications Whirlpool Pedestal WarrantyWarranty Whirlpool Washer WarrantyInstallation Information Installation RequirementsTools and Parts Optional PedestalWasher Dimensions Custom undercounter installationRecessed area or closet installation Standpipe drain system wall or floor view 1Remove Transport System Installation InstructionsFor a permanently connected washer Route the Drain Hose Connect the Inlet HosesSecure the Drain Hose To prevent drain water from going back into the washerComplete Installation Level the WasherInstallation Instructions Installing the Pedestal Page Theory of Operation IntroductionAir Vent System Pressure Switch Customer Interface and Cycle SelectionCycle Description Rinse/Spin SoakDrain/Spin Option Selection Options PrewashWater Temperature Guide ModifiersTouch Pad/LED Assembly Central Control Unit CCUDrive Motor Motor Control Unit MCUSuspension System Pump MotorEco Valve Heating Element Temperature Sensor Door Lock/Switch AssemblyPanel Interlock Switches Heating Element RelayPage Component Access Component LocationWasher TOP Washer BackComponent Access Accessing Components in the ConsoleRemoving the Washer Door and Door Switch 10 ScrewFrom the TUB Assembly Removing the BootReplacing the Boot Door Switch Removing the Detergent Dispenser Assembly Removing the Pump Assembly Removing Central Control Unit Pressure SwitchRemoving the Drive Motor Accessing Motor Control Unit Removing the Shock AbsorbersRemoving the TUB Basket Assembly Removing the Heating Element Temperature SensorRemoving the Heating Element Relay Front Shock Absorber Rear Shock Reassembling Reinstalling TUB Assembly Connector Location Component TestingCentral Control Unit Component Checks Dispenser Switch and Motor Test Points ReadingWater Level Test Points Reading Door Lock Main Switches Water Inlet Solenoids Test Points ReadingDrain Pump Motor Test Points Reading Door Lock/Unlock Solenoids Test Points ReadingMotor Control Unit Door Switch Test Points ReadingHeating Element Relay Solenoid Test Points Reading Line Filter DispenserPressure Switch Heating Element Relay SolenoidDiagnosis & Troubleshooting Suds DetectionDuring Drain Routine During Spin Extract RoutineDoor Locking and Unlocking LockingUnlocking Child Security RoutineUnbalance Detection Routine Error Codes Drive Motor Tachometer Error Motor Control Unit ErrorOverflow Condition Motor Control Unit MCU Heat Sink Thermal TripSerial Communication Error Dispenser Circuit ErrorEeprom Error Motor Control Unit MCU ErrorDoor Unlock Error Door Lock ErrorSeven, Tech Tips Diagnostic Test Starting the test modeTest Program Control during Execution Overview Test ProgramWater Temperature Sensor Motor Continuity TestTroubleshooting Guide Problem Possible CAUSE/TESTBasket WON’T Rotate Reading the Cycle Charts Pump Whirlpool GHW9200L Normal/Casual Quick Wash Whirlpool GHW9200L Whirlpool GHW9100L Normal/Casual Spin Profiles Spin Cycle LS1Spin Cycle LS2 Spin Cycle LS4 Spin Cycle LS3Spin Cycle ES Wiring Diagram Page Tech Tips Manual Door LatchDoor Plunger To Manually unlock the door lock systemPage Product Specifications Warranty Information Sources Corporation