Whirlpool GHW9200L, GHW9100L manual Door Locking and Unlocking, Child Security Routine

Page 46

DOOR LOCKING AND UNLOCKING

Locking

The Door Locking Routine will only start if the door is securely closed and the Door Switch Contact is CLOSED.

1.The Door Lock Relay is energized whenever a wash cycle is started. The relay is operated for 40 milliseconds.

2.During the next three (3) seconds, the contacts on the door lock are checked by the central control unit

a.If the contacts are CLOSED, this routine is finished.

b.If the contacts are still open after 3 seconds, the Central Control Unit energizes the Door Lock Relay for 40 ms and then checks the door lock contacts for 3 seconds. This will occur a maximum of 6 times. If the door is not locked after 6 trials, the Central Control Unit will enter a failure mode and the digital display will show FdL.

Unlocking

Unlocking will occur only under the following conditions:

1.The drive motor speed equals 0 or the time since the drive motor STOP command has been sent to the Motor Control Unit is greater than 180 seconds.

2.The time since the inlet valve was CLOSED is greater than five (5) seconds.

3.If the temperature of the water is greater than 122°F (50° C), the water will be drained before unlocking will occur.

4.If the water level is higher than the wash level in the Delicate, Wool or Handwash cycles, the water will be drained before unlocking will occur.

The Unlocking Routine is:

1.The Door Unlock Relay is energized for 40 ms.

2.During the next three (3) seconds, the contacts of the Door Lock are checked. If the con- tacts are OPEN, the Unlocking Routine is finished.

3.If the contacts are still CLOSED after three (3) seconds, the Central Control Unit ener- gizes the Door Unlock Relay for 40 ms. and then check the door lock contacts for three (3) seconds. If the door is not unlocked after 6 trials, the Central Control Unit will enter a failure mode and the digital display will show FdU.

Child Security Routine

The Child Security Routine is initiated at the start of any wash cycle.

1.The Door is Locked.

2.The tub fills with Cold water for three (3) seconds.

3.The door is Unlocked for five (5) seconds.

4.The door is Locked and the wash cycle begins.

6 - 2

Image 46
Contents Front-Loading Automatic Washer Model Numbers Forward Goal and ObjectivesTable of Contents Page Important Safety Information GeneralWhirlpool Model & Serial Number Designators Model Number G H W 9100 L WSpecifications Whirlpool Pedestal WarrantyWarranty Whirlpool Washer WarrantyTools and Parts Installation InformationInstallation Requirements Optional PedestalRecessed area or closet installation Washer DimensionsCustom undercounter installation Standpipe drain system wall or floor view 1Remove Transport System Installation InstructionsFor a permanently connected washer Secure the Drain Hose Route the Drain HoseConnect the Inlet Hoses To prevent drain water from going back into the washerComplete Installation Level the WasherInstallation Instructions Installing the Pedestal Page Theory of Operation IntroductionAir Vent System Pressure Switch Customer Interface and Cycle SelectionCycle Description Rinse/Spin SoakDrain/Spin Option Selection Options PrewashWater Temperature Guide ModifiersDrive Motor Touch Pad/LED AssemblyCentral Control Unit CCU Motor Control Unit MCUSuspension System Pump MotorEco Valve Panel Interlock Switches Heating Element Temperature SensorDoor Lock/Switch Assembly Heating Element RelayPage Washer TOP Component AccessComponent Location Washer BackComponent Access Accessing Components in the ConsoleRemoving the Washer Door and Door Switch 10 ScrewFrom the TUB Assembly Removing the BootReplacing the Boot Door Switch Removing the Detergent Dispenser Assembly Removing the Pump Assembly Removing Central Control Unit Pressure SwitchRemoving the Drive Motor Accessing Motor Control Unit Removing the Shock AbsorbersRemoving the TUB Basket Assembly Removing the Heating Element Temperature SensorRemoving the Heating Element Relay Front Shock Absorber Rear Shock Reassembling Reinstalling TUB Assembly Connector Location Component TestingCentral Control Unit Component Checks Dispenser Switch and Motor Test Points ReadingWater Level Test Points Reading Drain Pump Motor Test Points Reading Door Lock Main SwitchesWater Inlet Solenoids Test Points Reading Door Lock/Unlock Solenoids Test Points ReadingMotor Control Unit Door Switch Test Points ReadingHeating Element Relay Solenoid Test Points Reading Line Filter DispenserPressure Switch Heating Element Relay SolenoidDuring Drain Routine Diagnosis & TroubleshootingSuds Detection During Spin Extract RoutineUnlocking Door Locking and UnlockingLocking Child Security RoutineUnbalance Detection Routine Error Codes Overflow Condition Drive Motor Tachometer ErrorMotor Control Unit Error Motor Control Unit MCU Heat Sink Thermal TripEeprom Error Serial Communication ErrorDispenser Circuit Error Motor Control Unit MCU ErrorDoor Unlock Error Door Lock ErrorSeven, Tech Tips Test Program Control during Execution Diagnostic TestStarting the test mode Overview Test ProgramWater Temperature Sensor Motor Continuity TestTroubleshooting Guide Problem Possible CAUSE/TESTBasket WON’T Rotate Reading the Cycle Charts Pump Whirlpool GHW9200L Normal/Casual Quick Wash Whirlpool GHW9200L Whirlpool GHW9100L Normal/Casual Spin Profiles Spin Cycle LS1Spin Cycle LS2 Spin Cycle LS4 Spin Cycle LS3Spin Cycle ES Wiring Diagram Page Door Plunger Tech TipsManual Door Latch To Manually unlock the door lock systemPage Product Specifications Warranty Information Sources Corporation