Whirlpool GHW9200L Diagnostic Test, Starting the test mode, Test Program Control during Execution

Page 52

DIAGNOSTIC TEST

The control must be in the OFF state before pressing the touch-pad sequence to start the test.

Starting the test mode

Close the door.

Press the Control On button. Select the DRAIN/SPIN cycle.

Select NO SPIN by pressing the SPIN SELECT button, as needed.

Push Prewash Option button four (4) times within five (5) seconds. C:00 will show in the display. NOTE: If Model does not have PREWASH Mode as an option, press RINSE/HOLD.

If the Starting procedure fails, push PAUSE/CANCEL button. Then repeat the starting sequence.

Test Program Control during Execution

To advance to the next step of the test procedure, push Prewash Option button two (2) times.

Overview Test Program

Indication

Control Action

Actuators to be Checked

C:00

Door is Locked

Door Lock System

 

 

 

C:01

Filling by cold water inlet valve

Flowmeter, Cold water inlet valve

 

 

 

C:02

Distribution system is set to Prewash position

Dispenser motor,

 

 

Dispenser contact

 

 

 

C:03

Fill by hot water inlet valve

Hot water inlet valve

 

 

 

C:04

Basket rotates clockwise at wash speed

Motor, MCU control

 

 

 

C:05

Heater is switched ON.

Heater, Temperature Sensor

 

Basket rotates clockwise with wash speed.

 

 

If there is not enough water in the tub, the

 

 

water inlet valve will be switched ON to fill-in

 

 

the minimum water quantity.

 

 

NOTE: On GHW 9100 Models only the

 

 

Temperature Sensor will be checked

 

 

 

 

C:06

Drain Pump is ON

Drain Pump

 

 

 

C:07

Basket rotates counterclockwise

Motor, MCU control

 

from 35 to 90 rpm

 

 

within 15 seconds

 

 

 

 

C:08

Basket rotates counterclockwise

Motor, MCU control

 

with max. speed

 

 

Basket speed > 1100 rpm

 

 

 

 

6 - 8

Image 52
Contents Front-Loading Automatic Washer Model Numbers Forward Goal and ObjectivesTable of Contents Page Important Safety Information GeneralWhirlpool Model & Serial Number Designators Model Number G H W 9100 L WSpecifications Whirlpool Pedestal WarrantyWarranty Whirlpool Washer WarrantyInstallation Information Installation RequirementsTools and Parts Optional PedestalWasher Dimensions Custom undercounter installationRecessed area or closet installation Standpipe drain system wall or floor view 1Remove Transport System Installation InstructionsFor a permanently connected washer Route the Drain Hose Connect the Inlet HosesSecure the Drain Hose To prevent drain water from going back into the washerComplete Installation Level the WasherInstallation Instructions Installing the Pedestal Page Theory of Operation IntroductionAir Vent System Pressure Switch Customer Interface and Cycle SelectionCycle Description Rinse/Spin SoakDrain/Spin Option Selection Options PrewashWater Temperature Guide ModifiersTouch Pad/LED Assembly Central Control Unit CCUDrive Motor Motor Control Unit MCUSuspension System Pump MotorEco Valve Heating Element Temperature Sensor Door Lock/Switch AssemblyPanel Interlock Switches Heating Element RelayPage Component Access Component LocationWasher TOP Washer BackComponent Access Accessing Components in the ConsoleRemoving the Washer Door and Door Switch 10 ScrewFrom the TUB Assembly Removing the BootReplacing the Boot Door Switch Removing the Detergent Dispenser Assembly Removing the Pump Assembly Removing Central Control Unit Pressure SwitchRemoving the Drive Motor Accessing Motor Control Unit Removing the Shock AbsorbersRemoving the TUB Basket Assembly Removing the Heating Element Temperature SensorRemoving the Heating Element Relay Front Shock Absorber Rear Shock Reassembling Reinstalling TUB Assembly Connector Location Component TestingCentral Control Unit Component Checks Dispenser Switch and Motor Test Points ReadingWater Level Test Points Reading Door Lock Main Switches Water Inlet Solenoids Test Points ReadingDrain Pump Motor Test Points Reading Door Lock/Unlock Solenoids Test Points ReadingMotor Control Unit Door Switch Test Points ReadingHeating Element Relay Solenoid Test Points Reading Line Filter DispenserPressure Switch Heating Element Relay SolenoidDiagnosis & Troubleshooting Suds DetectionDuring Drain Routine During Spin Extract RoutineDoor Locking and Unlocking LockingUnlocking Child Security RoutineUnbalance Detection Routine Error Codes Drive Motor Tachometer Error Motor Control Unit ErrorOverflow Condition Motor Control Unit MCU Heat Sink Thermal TripSerial Communication Error Dispenser Circuit ErrorEeprom Error Motor Control Unit MCU ErrorDoor Unlock Error Door Lock ErrorSeven, Tech Tips Diagnostic Test Starting the test modeTest Program Control during Execution Overview Test ProgramWater Temperature Sensor Motor Continuity TestTroubleshooting Guide Problem Possible CAUSE/TESTBasket WON’T Rotate Reading the Cycle Charts Pump Whirlpool GHW9200L Normal/Casual Quick Wash Whirlpool GHW9200L Whirlpool GHW9100L Normal/Casual Spin Profiles Spin Cycle LS1Spin Cycle LS2 Spin Cycle LS4 Spin Cycle LS3Spin Cycle ES Wiring Diagram Page Tech Tips Manual Door LatchDoor Plunger To Manually unlock the door lock systemPage Product Specifications Warranty Information Sources Corporation