Whirlpool GHW9100L, GHW9200L manual Basket WON’T Rotate

Page 55

PROBLEM

POSSIBLE CAUSE/TEST

 

Note: Possible Cause/Tests MUST be performed in the sequence

 

shown for each problem.

 

 

 

OVER FILLS

1.

Verify the unit is level.

 

2.

Check pump drain system – this could indicate a failure to drain.

 

3.

Check Operating Pressure Switch.

 

4.

Check Pressure Switch hose.

 

5.

Check Flow Meter operation.

 

6.

Check the CCU.

 

 

 

BASKET WON’T ROTATE

1.

Check Drive belt.

 

2.

Check Drive motor.

 

3.

Check Wire Harness connections.

 

4.

Check Motor Control Unit.

 

 

 

MOTOR OVERHEATS

1.

Check Drive motor.

 

2.

Check Wire Harness connections.

 

3.

Check Drive belt.

 

4.

Check Motor Control Unit.

 

 

 

WON’T DRAIN

1.

Check Wire Harness connections.

 

2.

Check Drain pump.

 

3.

Check Drain pump motor.

 

4.

Check that the Drain hose and Drain Pump Filter is clear of

 

 

foreign objects.

 

5.

Check the CCU.

 

 

 

MACHINE VIBRATES

1.

Remove Shipping system.

 

2.

Check installation.

 

3.

Check leveling feet.

 

4.

Check leveling feet lock nuts.

 

5.

Check for weak floor.

 

 

 

INCORRECT WATER

1.

Check that the Inlet Hoses are connected properly.

TEMPERATURE

2.

Check the Water Heater and Wire Harness connections to it.

 

3.

Check Water Temperature Sensor for an abnormal condition.

 

4.

Check the CCU.

 

 

 

6 - 11

Image 55
Contents Front-Loading Automatic Washer Model Numbers Goal and Objectives ForwardTable of Contents Page General Important Safety InformationModel Number G H W 9100 L W Whirlpool Model & Serial Number DesignatorsWhirlpool Pedestal Warranty SpecificationsWhirlpool Washer Warranty WarrantyOptional Pedestal Installation InformationInstallation Requirements Tools and PartsStandpipe drain system wall or floor view 1 Washer DimensionsCustom undercounter installation Recessed area or closet installationRemove Transport System Installation InstructionsFor a permanently connected washer To prevent drain water from going back into the washer Route the Drain HoseConnect the Inlet Hoses Secure the Drain HoseLevel the Washer Complete InstallationInstallation Instructions Installing the Pedestal Page Introduction Theory of OperationAir Vent System Customer Interface and Cycle Selection Pressure SwitchCycle Description Rinse/Spin SoakDrain/Spin Option Selection Prewash OptionsModifiers Water Temperature GuideMotor Control Unit MCU Touch Pad/LED AssemblyCentral Control Unit CCU Drive MotorSuspension System Pump MotorEco Valve Heating Element Relay Heating Element Temperature SensorDoor Lock/Switch Assembly Panel Interlock SwitchesPage Washer Back Component AccessComponent Location Washer TOPAccessing Components in the Console Component Access10 Screw Removing the Washer Door and Door SwitchFrom the TUB Assembly Removing the BootReplacing the Boot Door Switch Removing the Detergent Dispenser Assembly Removing the Pump Assembly Removing Central Control Unit Pressure SwitchRemoving the Drive Motor Removing the Shock Absorbers Accessing Motor Control UnitRemoving the TUB Basket Assembly Removing the Heating Element Temperature SensorRemoving the Heating Element Relay Front Shock Absorber Rear Shock Reassembling Reinstalling TUB Assembly Connector Location Component TestingCentral Control Unit Component Checks Dispenser Switch and Motor Test Points ReadingWater Level Test Points Reading Door Lock/Unlock Solenoids Test Points Reading Door Lock Main SwitchesWater Inlet Solenoids Test Points Reading Drain Pump Motor Test Points ReadingMotor Control Unit Door Switch Test Points ReadingHeating Element Relay Solenoid Test Points Reading Dispenser Line FilterHeating Element Relay Solenoid Pressure SwitchDuring Spin Extract Routine Diagnosis & TroubleshootingSuds Detection During Drain RoutineChild Security Routine Door Locking and UnlockingLocking UnlockingUnbalance Detection Routine Error Codes Motor Control Unit MCU Heat Sink Thermal Trip Drive Motor Tachometer ErrorMotor Control Unit Error Overflow ConditionMotor Control Unit MCU Error Serial Communication ErrorDispenser Circuit Error Eeprom ErrorDoor Unlock Error Door Lock ErrorSeven, Tech Tips Overview Test Program Diagnostic Test Starting the test mode Test Program Control during ExecutionMotor Continuity Test Water Temperature SensorProblem Possible CAUSE/TEST Troubleshooting GuideBasket WON’T Rotate Reading the Cycle Charts Pump Whirlpool GHW9200L Normal/Casual Quick Wash Whirlpool GHW9200L Whirlpool GHW9100L Normal/Casual Spin Cycle LS1 Spin ProfilesSpin Cycle LS2 Spin Cycle LS4 Spin Cycle LS3Spin Cycle ES Wiring Diagram Page To Manually unlock the door lock system Tech TipsManual Door Latch Door PlungerPage Product Specifications Warranty Information Sources Corporation