Beko WMG 10454 W Connecting water supply, Inlet, blue hose right max ºC is for cold water inlet

Page 14

4.4.4 Connecting water supply

CThe water supply pressure required to run the product is between 1 to 10 bars (0.1 – 1 MPa). It is necessary to have 10 – 80 liters of water flowing from the fully open tap in one minute to have your machine run smoothly. Attach a pressure reducing valve if water pressure is higher.

If you are going to use the double water-inlet product as a single (cold) water-inlet unit, you must install the supplied stopper to the hot water valve before operating the product. (Applies for the products supplied with a blind stopper group.)

A CAUTION: Models with a single water inlet should not be connected to the hot water tap. In such a case the laundry will get damaged or the product will switch to protection mode and will not operate.

CAUTION: Do not use old or used water inlet hoses on the new product. It may cause stains on your laundry.

Connect the special water supply hoses supplied with the product to the water inlets on the product. Red hose (left) (max. 90 ºC) is for hot water

inlet, blue hose (right) (max. 25 ºC) is for cold water inlet.

Make sure that the hot and cold water taps are connected correctly when

the product is being installed. Otherwise, your laundry will come out hot at the end of the washing process and wear out.

1Tighten the nuts of the hose by hand. Never use a tool when tightening the nuts.

2When hose connection is completed, check whether there is leak problems at the connection points by opening the taps fully. If any leaks occur, turn off the tap and remove the nut. Retighten the nut carefully after checking the seal. In order to prevent the water leaks and resultant damages, keep the taps closed when you do not use the product.

14 / EN

Washing Machine / User’s Manual

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Washing Machine Explanation of symbols Dear CustomerGeneral safety instructions Troubleshooting General safety instructions Childrens safety Electrical safety Compliance with Weee Directive Package informationYour washing machine OverviewPackage Contents Rated capacity kg Technical specifications11 / EN 12 / EN InstallationDo not place the product on the power cable Removing packaging reinforcement 13 / EN14 / EN Connecting water supplyInlet, blue hose right max ºC is for cold water inlet Connecting the drain hose to the drain An appropriate clamp as not to come off and leak 15 / EN16 / EN Fitting a different plug 17 / ENPreparation 18 / ENPreparing laundry for washing 19 / ENUsing detergent and softener 20 / EN21 / EN Using gel and tablet detergent 22 / ENSoiled Tips for efficient washingHeavily NormallyOperating the product Programme and consumption table 25 / EN26 / EN 014127 / EN Programme selectionProgrammes BabyClothing AutoCottons Eco GentleCare29 / EN Use when you want to rinse or starch separatelyUse to drain the water in the machine Temperature selection This function holds the laundry in the final rinsing water Programme is displayed on the Spin Speed indicatorSpin speed selection 30 / ENAuxiliary function selection 31 / ENQuicker Wash Night ModePrewash Extra RinseEnd Time 33 / EN34 / EN To deactivate the childproof lock 35 / EN36 / EN Maintenance and cleaning 37 / ENClose the taps Pull the emergency draining hose out from its seat Draining remaining water and cleaning the pump filterOrder to clean the dirty filter and discharge the water Absorb any spilled water Problem Reason Solution 41 / ENManual 42 / ENWashing takes longer With display43 / EN Laundry became stiff 44 / ENIt does not rinse well After washing45 / EN Page Washing Machines 0845 600 UK Mainland & Northern IrelandRepublic of Ireland Guarantee
Top Page Image Contents