Hotpoint WD865, WD860 manual Connect your machine to the water supply, Hot and cold fill

Page 8

4. Connect your machine to the water supply...

INSTALLING YOUR MACHINE

WARNINGS:

The temperature of your hot water supply should ideally be 60°C and no higher than 70°C as this could cause damage to your laundry and the machine.

Do not connect the machine to a single outlet instantaneous water heater.

Your hot and cold water pressure must be in the range Max. 1Mpa (10 bar) and Min. 0.05Mpa (0.5 bar). Incorrect pressures could lead to flooding.

The water supply taps should be accessible when the machine is installed.

Before connecting the fill hoses, check that water is running from the water supply taps you will use for your machine.

Connect the machine to the water supply using the fill hoses fitted to the machine. Do not use old hoses.

Hot and cold fill

1Unclip both of the fill hoses from the back of the machine.

2 Connect the free end of the grey fill hose with the red connector to the HOT water supply (see figure1). Connect the free end of the grey fill hose with the blue connector to the COLD water supply.

3 Turn on your water supply and check for leaks.

If there is a leak, turn off the water supply, remove the connector and check that the sealing washer is in place. Refit the connector and tighten it.

Turn on the water supply.

4 When moving the machine into its final position, make sure that the hoses are not trapped or kinked.

figure 1

 

figure 2

 

 

 

If the fill hoses are too short:

Longer fill hoses are available from our Genuine Parts and Accessories Mail Order Hotline UK on 08709 077 077 or www.theservicecentre.co.uk (or in the Republic of Ireland on (01) 842 6836).

Remove the existing fill hoses from the inlet valves on the back of the machine and fit the new longer fill hoses as

cold water supply shown above with the angled ends of the hoses connected to the machine (see figure 2).

figure 3

If you have no hot water supply or your hot water pressure is low:

A cold fill adaptor (figure 3) and fitting instructions are available from your local Hotpoint authorised Service Centre or by calling the Genuine Parts and Accessories Mail Order Hotline UK on 08709 077 077 or www.theservicecentre.co.uk

(or in the Republic of Ireland on (01) 842 6836).

8

Image 8
Contents Instructions Congratulations on choosing Ultima Typical wash and dry programme Safety first Choose a location Installing your machineRemove the polystyrene base Remove the transit fixings Repeat steps 1 to 4 to remove the second transit boltConnect your machine to the electricity supply If the fill hoses are too short Connect your machine to the water supplyHot and cold fill Connect the machine to a drainage system Once the machine is in place Adjust the feetMove the machine into position Washcare tips = 6kg= 3kg Before washing laundry we recommend that you do FollowingDo not try to open the door when a programme is running Typical wash & dry programmeShooting section ‘ON/OFF Pause’If you wish to use liquid detergent Dispenser drawerChoose a suitable detergent Using in-drum dosing Dispensing liquid detergentDispensing tablets Pre-washWash programmes Programme times ‘Time to End’ Fabric type Acrylics and Synthetics Display Wash Maximum An intensive wash programme Dry programmes Drycare tips= 5kg Items not suitable for tumble dryingIndependent drying programme Misuse of the dryer may create a fire hazardSpin only programmes Time Saver OptionsChoosing an option button Automatic Features Pre WashAuto half load Unbalanced load warningDrying Heat button Sensor Dry button Timed Dry button Cleaning the outside Cleaning and maintenanceMaintenance wash Trouble Shooting Troubleshooting Cannot read the information Display windowHotpoint guarantee Guarantee terms and conditionsAfter sales service Available on our web-site atPage Page Key contacts