American Dryer Corp AD-95 Pulleys To Replace Drive Shaft Pulley, To Replace Drive Motor Pulley

Page 32

5. Reestablish power to dryer.

F. Pulleys

To Replace Drive Shaft Pulley

1.Discontinue power to dryer.

2.Remove front panel from dryer (Follow front

replacement directions on page 27.)

3. Loosen v-belts. Rotate pulley and roll v-belts out of grooves.

4. Remove set screw from the 9" pulley.

5. Remove pulley and key.

NOTE: A gear puller may be required to remove pulley.

6.Reverse this procedure for replacement.

NOTE: Pulley must be aligned for proper operation.

To Replace Drive Motor Pulley

1.Discontinue power to dryer.

2.Remove front panel from the dryer. Follow front panel replacement directions on page 27.

3.Loosen v-belts. Rotate pulley and roll v-belt out of groove.

4.Remove set screw from the drive motor pulley.

5.Remove pulley and key.

NOTE: A gear puller may be required to remove pulley.

6.Reverse this procedure for replacement.

NOTE: Pulleys must be aligned for proper operation.

Tumbler Wheel Replacement on Drive Assembly (taper lock models)

1.Discontinue power to dryer.

2.Remove front panel from dryer. (Follow front panel replacement directions on page 27.)

3.Remove the ten (10) 1/4-20 x 1/4" socket button head screws from the perfed basket side.

4.Remove wrapper assembly.

5.Loosen v-belts. Rotate pulley and v-belts out of the groove.

6.Block the basket (tumbler) assembly in position.

7.Mark the position of pillow block bearing then remove the bolts from the pillow block bearings.

8.Remove the drive shaft assembly through the front of the machine.

9.Remove the set screw from the 9" pulley.

28

Image 32
Contents AD-95/ML-95 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Content Troubleshooting Safety Precautions SectionCleaning WeeklyDays MonthsLubrication AdjustmentsSeven Days after Installation and every 6 Months Enclosure, Air Supply, and Exhaust Requirements Electrical and Gas RequirementsOperational Service Check Procedure Prior to February 11 Control Panel Microprocessor As of February 11With circuit breaker Reversing Relay Panel With fusesGas Burner Assembly HSI Module Gas ModelsDrive Motor Blower Motor and ImpellerTaperlock Trantorque Drive Shaft Assembly Idler Shaft Assembly Transtorque TaperlockMain Door Switch Basket TumblerSail Switch Gas Models Only Hi-Limit Gas Models OnlyAutomatic Reset Thermostat Lint ScreenLint Drawer Switch Servicing Computer ControlsTo Replace Keyboard Label Assembly HSI Ignitor Flame Sensor Probe Ignition ControlsTo Remove Flame Sensor Probe To Replace Main Burner Orifices To Test and Adjust Gas Water Column PressureTo Replace Gas Valve See burner illustration on To Convert Natural Gas to L.P. Gas To Replace Burner TubesDiscontinue power to the dryer To Replace HSI ModuleTo Adjust Sail Switch Sail Switch Assembly Gas Models OnlyTo Replace Sail Switch To Replace Main Door Switch To Replace Main Door AssemblyTo Install New Main Door Glass as of October 24 Front Panel and Main Door AssembliesAs of October 24 Prior to October 24 To Replace Main Door Hinge Block To Install new Main Door Glass prior of October 24To Replace Front Panel Pulleys To Replace Drive Shaft Pulley To Replace Drive Motor PulleyPage Tumbler Wheel Replacement on IdlerAssembly taper lock models Tumbler Wheel Replacement on IdlerAssembly trantorque models To Replace Blower Shaft PulleyBasket Assembly To Replace Blower Motor PulleyTo Replace Idler Shaft Pillow Block Bearing To Replace Drive Assembly Pillow Block BearingBelt Adjustment Motor to Drive Axle To Replace Impeller Motor Fan Shaft Drive To Replace Drive Motor V-BeltsMotors To Replace Blower Motor V-belts To Replace Front Thruster WheelsRear Access ImpellerTo Replace Lint Screen Lint Screen AssemblyTo Replace Lint Door Switch No display on computer Computer will not accept key pad entriesDryer will not start, but computer display indictors are on Drive motor runs, burner is on, but basket will not turnOverload for impeller fan motor is tripping Burner hi-limit safety thermostat is trippingThermal overload for drive motor is tripping There is excessive vibration coming from the basket Phase 6 OPL System Diagnostics Page E.D. Display Indicators E.D Display Indicator Number AIR AIR JET Output L.E.D. Indicator Optional FAN Blower Output L.E.D. IndicatorFuse Main Fuse Input L.E.D. Indicator Flame bURNER Control Fail Input L.E.D. Indicator E.D. Codes BURNER Safety Fail DRUM Safety FailBURNER Control Fail BURNER Flame FailComputer Logic and Wiring Diagram No Display Condition Drive motor reverses but does not forward, blower motor runs Blower motor does not operate, drive motor runsLint Door Condition Main Door ConditionMicroprocessor Which Must be Reset Manually Technical Information For exampleData Label HOW to USE a Manometer AD-95/ML-95 Tool List ADC450188 1- 01/14/99-25