American Dryer Corp AD-95 service manual Ignition Controls, To Remove Flame Sensor Probe

Page 24

B. Ignition Controls

To Remove Hot Surface Ignitor (see burner illustration on page 10)

1. Discontinue power to dryer.

2. Disconnect wire from S1 and GND on the HSI module.

3. Disassemble ignitor from burner by removing the one (1) self tapping screw.

4. Reverse procedure for installation of new ignitor.

To Remove Flame Sensor Probe

1.Discontinue power to dryer.

2.Disconnect the red wire from the flame sensor probe which goes to S2 on the HSI module.

3.Disassemble flame sensor probe from burner by removing the one (1) self tapping screw.

4.Reverse procedure for installation of new flame sensor probe.

HSI Ignitor Flame Sensor Probe

NOTE: Before reestablishing power to dryer visually check the following (see illustration)

A.That the hot surface ignitor wires are connected to S1 and GND on the HSI module.

B.Do not wrap the hot surface ignitor wires and the flame electrode wire together. Improper operation may result. They may run alongside each other.

20

Image 24
Contents AD-95/ML-95 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Content Troubleshooting Safety Precautions SectionCleaning WeeklyDays MonthsAdjustments Seven Days after Installation and every 6 MonthsLubrication Enclosure, Air Supply, and Exhaust Requirements Electrical and Gas RequirementsOperational Service Check Procedure Prior to February 11 Control Panel Microprocessor As of February 11With circuit breaker Reversing Relay Panel With fusesGas Burner Assembly HSI Module Gas ModelsDrive Motor Blower Motor and ImpellerTaperlock Trantorque Drive Shaft Assembly Idler Shaft Assembly Transtorque TaperlockMain Door Switch Basket TumblerSail Switch Gas Models Only Hi-Limit Gas Models OnlyAutomatic Reset Thermostat Lint ScreenLint Drawer Switch Servicing Computer ControlsTo Replace Keyboard Label Assembly Ignition Controls To Remove Flame Sensor ProbeHSI Ignitor Flame Sensor Probe To Test and Adjust Gas Water Column Pressure To Replace Gas Valve See burner illustration onTo Replace Main Burner Orifices To Convert Natural Gas to L.P. Gas To Replace Burner TubesDiscontinue power to the dryer To Replace HSI ModuleSail Switch Assembly Gas Models Only To Replace Sail SwitchTo Adjust Sail Switch To Replace Main Door Switch To Replace Main Door AssemblyTo Install New Main Door Glass as of October 24 Front Panel and Main Door AssembliesAs of October 24 Prior to October 24 To Install new Main Door Glass prior of October 24 To Replace Front PanelTo Replace Main Door Hinge Block Pulleys To Replace Drive Shaft Pulley To Replace Drive Motor PulleyPage Tumbler Wheel Replacement on IdlerAssembly taper lock models Tumbler Wheel Replacement on IdlerAssembly trantorque models To Replace Blower Shaft PulleyBasket Assembly To Replace Blower Motor PulleyTo Replace Drive Assembly Pillow Block Bearing Belt Adjustment Motor to Drive AxleTo Replace Idler Shaft Pillow Block Bearing To Replace Drive Motor V-Belts MotorsTo Replace Impeller Motor Fan Shaft Drive To Replace Blower Motor V-belts To Replace Front Thruster WheelsRear Access ImpellerLint Screen Assembly To Replace Lint Door SwitchTo Replace Lint Screen No display on computer Computer will not accept key pad entriesDryer will not start, but computer display indictors are on Drive motor runs, burner is on, but basket will not turnBurner hi-limit safety thermostat is tripping Thermal overload for drive motor is trippingOverload for impeller fan motor is tripping There is excessive vibration coming from the basket Phase 6 OPL System Diagnostics Page E.D. Display Indicators E.D Display Indicator Number AIR AIR JET Output L.E.D. Indicator Optional FAN Blower Output L.E.D. IndicatorFuse Main Fuse Input L.E.D. Indicator Flame bURNER Control Fail Input L.E.D. Indicator E.D. Codes BURNER Safety Fail DRUM Safety FailBURNER Control Fail BURNER Flame FailComputer Logic and Wiring Diagram No Display Condition Drive motor reverses but does not forward, blower motor runs Blower motor does not operate, drive motor runsLint Door Condition Main Door ConditionMicroprocessor Which Must be Reset Manually Technical Information For exampleData Label HOW to USE a Manometer AD-95/ML-95 Tool List ADC450188 1- 01/14/99-25