American Dryer Corp AD-95 service manual To Replace Drive Motor V-Belts, Motors

Page 38

8.Retighten motor mount bolts and jam nuts.

9.Assemble front panel lint door assemblies back to dryer.

10.Reestablish power to dryer.

To Replace Drive Motor V-Belts

1.Discontinue power to the dryer.

2.Remove front panel. Follow front panel replacement instructions on page 27.

3.Loosen tension on v-belt so that it can easily be rolled off pulley. This can be done by loosening the four bolts holding the motor to the side of the dryer. As well as the adjustment bolt on top.

4.Replace v-belt.

5.Retighten v-belt and adjust tension and alignment per previous instructions.

J. Motors

To Replace Drive Motor

1. Discontinue power to dryer.

2. Remove front panel from dryer. Follow front panel replacement instructions on page 27.

3. Remove drive belt.

4. Disconnect wiring harness from motor.

5. Remove bolts holding motor to mount and replace with new motor. Do not tighten bolts.

6. Remove pulley from old motor and install on new motor. By removing the set screw from the drive motor pulley.

NOTE: A gear puller may be required to remove pulley.

7.Align motor pulley with drive assembly pulley and tighten set screw holding motor pulley.

8.Replace belts and adjust belt tension.

9.Retighten bolts.

10.Reestablish power to dryer.

To Replace Impeller Motor (Fan Shaft Drive)

1.Discontinue power to the dryer.

2.Remove lint door and front panel from dryer.

3.Remove the perforated panel inside the basket (tumbler).

4.Remove the wrapper assembly under the basket.

34

Image 38

Contents AD-95/ML-95 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Content Troubleshooting Safety Precautions SectionDays CleaningWeekly MonthsLubrication AdjustmentsSeven Days after Installation and every 6 Months Enclosure, Air Supply, and Exhaust Requirements Electrical and Gas RequirementsOperational Service Check Procedure Prior to February 11 Control Panel Microprocessor As of February 11With circuit breaker Reversing Relay Panel With fusesGas Burner Assembly HSI Module Gas ModelsDrive Motor Blower Motor and ImpellerTaperlock Trantorque Drive Shaft Assembly Idler Shaft Assembly Transtorque TaperlockMain Door Switch Basket TumblerSail Switch Gas Models Only Hi-Limit Gas Models OnlyAutomatic Reset Thermostat Lint ScreenLint Drawer Switch Servicing Computer ControlsTo Replace Keyboard Label Assembly HSI Ignitor Flame Sensor Probe Ignition ControlsTo Remove Flame Sensor Probe To Replace Main Burner Orifices To Test and Adjust Gas Water Column PressureTo Replace Gas Valve See burner illustration on To Convert Natural Gas to L.P. Gas To Replace Burner TubesDiscontinue power to the dryer To Replace HSI ModuleTo Adjust Sail Switch Sail Switch Assembly Gas Models OnlyTo Replace Sail Switch To Install New Main Door Glass as of October 24 To Replace Main Door SwitchTo Replace Main Door Assembly Front Panel and Main Door AssembliesAs of October 24 Prior to October 24 To Replace Main Door Hinge Block To Install new Main Door Glass prior of October 24To Replace Front Panel Pulleys To Replace Drive Shaft Pulley To Replace Drive Motor PulleyPage Tumbler Wheel Replacement on IdlerAssembly taper lock models Tumbler Wheel Replacement on IdlerAssembly trantorque models To Replace Blower Shaft PulleyBasket Assembly To Replace Blower Motor PulleyTo Replace Idler Shaft Pillow Block Bearing To Replace Drive Assembly Pillow Block BearingBelt Adjustment Motor to Drive Axle To Replace Impeller Motor Fan Shaft Drive To Replace Drive Motor V-BeltsMotors To Replace Blower Motor V-belts To Replace Front Thruster WheelsRear Access ImpellerTo Replace Lint Screen Lint Screen AssemblyTo Replace Lint Door Switch Dryer will not start, but computer display indictors are on No display on computerComputer will not accept key pad entries Drive motor runs, burner is on, but basket will not turnOverload for impeller fan motor is tripping Burner hi-limit safety thermostat is trippingThermal overload for drive motor is tripping There is excessive vibration coming from the basket Phase 6 OPL System Diagnostics Page E.D. Display Indicators E.D Display Indicator Number AIR AIR JET Output L.E.D. Indicator Optional FAN Blower Output L.E.D. IndicatorFuse Main Fuse Input L.E.D. Indicator Flame bURNER Control Fail Input L.E.D. Indicator E.D. Codes BURNER Control Fail BURNER Safety FailDRUM Safety Fail BURNER Flame FailComputer Logic and Wiring Diagram No Display Condition Drive motor reverses but does not forward, blower motor runs Blower motor does not operate, drive motor runsLint Door Condition Main Door ConditionMicroprocessor Which Must be Reset Manually Technical Information For exampleData Label HOW to USE a Manometer AD-95/ML-95 Tool List ADC450188 1- 01/14/99-25