Bradley Smoker EXD-2N installation instructions Optional hot water heater, Completing installation

Page 9

 

Express® Deck Lavatory System EXD-Series

Installation Instructions

EXD-2N

 

 

Installation Instructions continued . . .

Step 5: Optional hot water heater

WARNING: To avoid personal injury or damage to the unit when installing the water heater, make all plumbing connections first, then proceed with the electrical connections.

NOTE: 240/208 or 277 voltage is required

 

 

 

 

 

for hot water heater. Refer to the

 

 

#8 NUT

 

installation manual provided with the hot

BRACKET

 

#8 WASHER

 

 

water heater for further installation

 

 

 

 

 

 

 

 

 

information.

 

 

 

 

 

1. Remove the cover from the water

 

 

 

 

 

heater. Attach the bracket to the cover

 

 

 

 

 

with the two screws, nuts and

#8-32 x 3/4"

 

 

 

 

washers, then reattach the cover (see

MACHINE SCREW

 

 

 

 

 

ROUND HEAD

 

 

 

 

Figure 6a).

 

 

 

 

 

2. Hang the water heater on the right

 

 

 

 

 

side frame member (see Figure 6b).

WATER

 

 

 

 

3. Connect the 1/2" flexible hose from

HEATER

 

 

 

 

BASE

 

 

 

 

the cold water supply stub-out to the

 

 

 

 

HEATER

hot water heater inlet.

 

 

 

 

 

 

 

 

 

WATER

4. Connect the 1/2" flexible hose from

Figure 6a

 

 

 

COVER

 

 

 

 

 

the hot water heater outlet to the

 

 

 

 

 

supply inlet on the solenoid valve

 

 

 

 

 

assembly.

PREPACKS:

 

 

 

 

Step 6: Completing installation

EX95TMLB (S45-2186)

OPTIONAL 90˚ ELBOW

 

 

EX100TMLB (S45-2187)

 

 

 

 

 

 

 

1. Install the faucets according to the

 

 

CHECK/STOP

 

 

installation instructions that came

 

 

 

 

 

 

VALVE

 

 

with your faucets.

 

 

 

 

 

2. Turn on the water supply to the

 

 

 

 

 

Express® Deck and check for

 

 

 

 

 

leaks.

 

 

 

 

 

3. FOR DECKS WITH INFRARED

 

 

 

 

 

FAUCETS ONLY: Turn on the

 

 

 

 

 

electrical power to the electrical

 

 

 

 

 

outlet and pass your hand in front

 

 

 

 

 

of each faucet’s sensor until all

 

 

 

 

 

the air is purged from the lines

 

 

 

 

 

and water is flowing smoothly.

 

 

 

INLET

WATER

4. After testing is complete, reinstall

 

 

OUTLET TO

COLD WATER

 

HEATER

 

FAUCETS

 

 

panel to frame. Fasten panel with

SUPPLY

 

 

 

 

 

 

 

 

 

eight Torx-head screws provided

Figure 6b

 

 

 

 

(see Figure 2 on page 6).

 

 

 

 

 

Bradley Corporation • 215-1542 Rev. E; EN 06-915

2/9/07

9

Image 9
Contents Express Deck Lavatory System EXD-Series Installation InstructionsEXD-2N Standard Height Installation Instructions Supplies required for installationRough Option #2 EXD-2N Express Deck Lavatory System DimensionsMounting frame to wall Procedure #3 on page 4 FigureInstalling bowl Connecting supply and drain Optional hot water heater Completing installationTerreon and panel maintenance Cleaning and Maintenance InstructionsCleaning Panel cleaningPrepack Assembly of ComponentsThermostatic Mixing Valve Maintenance and Troubleshooting Problem Limited water flowProblem External leaks in the system Repair Kit S65-259 Vernatherm Thermostatic Mixing Valve S01-524