Kenmore 796. 8147#, 796.9147# Final Installation Check, Testing Dryer Heating, Checking Venting

Page 17

FINAL INSTALLATION CHECK

Once you have completed the installation of the dryer and it is in its final location, confirm proper operation with the following steps and tests.

1Is gas turned on? (Gas models only)

2Is dryer plugged in? Dryer should always be plugged into the proper outlet.

Gas dryer should use a

120-VAC, 60-Hz. grounded

3-prong outlet.

Electric dryer should use a

4-wire connection which is required for all mobile and manufactured home installations, as well as all new construction after

January 1, 1996.

-- OR --

A 3-wire connection. NOTE: A 3-wire connection is NOT permitted on new construction after January 1, 1996.

3Is the dryer transition duct from dryer to wall connected? Make sure the transition duct behind the dryer is properly connected and is not crushed or damaged.

4Is dryer level? Once the dryer is in its final location, recheck the dryer to be sure it is level. Make sure it is level front to back and side to side, and that all four leveling feet rest firmly on the floor.

5Is the dryer heating normally? Perform the following dryer heating test.

INSTALLATION INSTRUCTIONS

Testing Dryer Heating

1Close the dryer door.

2Press the POWER button to turn the dryer on.

3Turn the cycle selector knob to Normal drying cycle.

4Press the START/PAUSE to start the dryer. After three minutes, open the dryer door and check that the air inside is warm.

NOTE: If the air inside the dryer is not warm after three minutes, there may be air in the gas supply line to the dryer, and the gas igniter may turn off before the main burner ignites. When this happens, the igniter will continue to attempt main burner ignition until all air is purged from the line. Once ignition occurs, the air inside the dryer will become warm.

Checking Venting

Vent ductwork should be checked for lint buildup and cleaned at least once per year. If any noticeable reduction in drying performance occurs, check duct for obstructions and blockages.

17

Image 17
Contents Steam Dryer Installation Instructions Features and BenefitsHOW to USE Troubleshooting GuideRead ALL Instructions Before USE Basic Safety Precautions Weather Follow basic precautions, including the followingSafety Instructions for Steam Functions KEY Parts and Components Additional instructions for closet installations KEY Dimensions and SpecificationsLocation Requirements Choose the Proper LocationOptional Accessories Installation with Optional Pedestal Base or Stacking KITElectrical Requirements for GAS Models only Connecting GAS DryersHigh-Altitude Installations Connecting the Gas SupplyGas shutoff valve must be installed within 6 ft Proceed to Venting the DryerConnecting Electric Dryers Electrical Requirements Four-Wire Power Cord Connecting Electric DryersThree-Wire Power Cord As well as all new construction after January 1Using the Duct Length Chart below Venting the Dryer Routing and Connecting DuctworkConnecting the Dryer Vent Leveling the Dryer Wear gloves during installationReversing the Door Swing Hole capChecking Venting Final Installation CheckTesting Dryer Heating Control Panel Features Operating the Dryer Auto Dry Cycles Cycle Guide= available option = default settingFabric Care Labels Sorting LoadsGroup Similar Items Loading the DryerTime and Status Display Temp Cycle Modifier ButtonsDRY Level Timed DRYTo recall a MY Cycle Cycle Options and Special FeaturesTo save a MY Cycle Using the Steam Refresh cycle Steam FeaturesUsing the Static Shield option Using the Iron Ready optionFilling the Steam Feeder Steam FeaturesDrawer Pull out the drawer Lift out the steam feeder Tap waterCleaning the Exterior Regular CleaningCleaning the Interior Cleaning Around and Under the DryerMaintaining the Exhaust System Check Vent IndicatorMaintaining the Exhaust System Check Vent OperationKenmore Connect System Using the Kenmore Connect SystemProblem Possible Cause Solutions Before Calling for ServiceDry Before Calling for Service Problem Possible Cause SolutionsClothes are wrinkled Clothes are shrinkingSteam Features Not Display shows errorCode tE1 or tE2 Lint on clothes WorkingDisclaimer of implied warranties limitation of remedies Kenmore Elite Limited Warranty