Kenmore 796. 8147#, 796.9147# manual = available option, = default setting

Page 21

HOW TO USE

CYCLE GUIDE

The cycle guide below shows the available options and recommended fabric types for TIMED DRY cycles.

Timed Dry Cycles

Use Timed Dry cycles to select a specific amount of drying time and the drying temperature. When a TIMED DRY cycle is selected, the display shows the actual time remaining in your cycle.

You can change the actual time for the cycle by pressing MORE TIME or LESS TIME. Press and hold the MORE TIME or LESS TIME buttons to rapidly change the time.

Type

TIMED DRY

							= available option
								= default setting



			Modifiers				Options

				*Time in	More	Wrinkle	Damp			Static	Iron
Cycle	Fabric Type	Temperature	Dry Level	*Time in	Time/Less	Wrinkle	Dry			Static	Iron
Cycle	Fabric Type	Temperature	Dry Level	Min.	Time/Less	Guard	Dry			Shield	Ready
				Min.	Time	Guard	Signal			Shield	Ready
					Time		Signal
Express Dry	For small loads with	High	Off	25
Express Dry	short drying times	Adjustable		Max. 99
	short drying times


Touch Up	For removing light	Mid high	Off	20
	For removing light
	wrinkles	Adjustable		Max. 99
	wrinkles


	For items that	Off	Off	50
Air/Rack Dry	require heat-free
	require heat-free
	drying such as	Adjustable		Max. 99
	drying such as
	plastics or rubber
	plastics or rubber

	For general drying.	High	Off	40
Timed Dry*	Time, temperature,
	Time, temperature,
	and options can be	Adjustable		Max. 99
	and options can be
	set manually
	set manually

NOTE: To protect your garments, not every temperature or option is available with every cycle. Temperature settings cannot be changed. A different chime will sound and the LED will not illuminate if the selection is not allowed.

*Timed Dry is accessed by pressing the Timed Dry button in the Cycle Modifiers field of the of the Control Panel.

21

Image 21

Contents Steam Dryer Installation Instructions Features and BenefitsHOW to USE Troubleshooting GuideRead ALL Instructions Before USE Basic Safety Precautions Weather Follow basic precautions, including the followingSafety Instructions for Steam Functions KEY Parts and Components Additional instructions for closet installations KEY Dimensions and SpecificationsLocation Requirements Choose the Proper LocationOptional Accessories Installation with Optional Pedestal Base or Stacking KITElectrical Requirements for GAS Models only Connecting GAS DryersHigh-Altitude Installations Connecting the Gas SupplyGas shutoff valve must be installed within 6 ft Proceed to Venting the DryerConnecting Electric Dryers Electrical Requirements Four-Wire Power Cord Connecting Electric DryersThree-Wire Power Cord As well as all new construction after January 1Using the Duct Length Chart below Routing and Connecting Ductwork Connecting the Dryer VentVenting the Dryer Leveling the Dryer Wear gloves during installationReversing the Door Swing Hole capFinal Installation Check Testing Dryer HeatingChecking Venting Control Panel Features Operating the Dryer Auto Dry Cycles Cycle Guide= available option = default settingFabric Care Labels Sorting LoadsGroup Similar Items Loading the DryerTime and Status Display Temp Cycle Modifier ButtonsDRY Level Timed DRYCycle Options and Special Features To save a MY CycleTo recall a MY Cycle Using the Steam Refresh cycle Steam FeaturesUsing the Static Shield option Using the Iron Ready optionFilling the Steam Feeder Steam FeaturesDrawer Pull out the drawer Lift out the steam feeder Tap waterCleaning the Exterior Regular CleaningCleaning the Interior Cleaning Around and Under the DryerMaintaining the Exhaust System Check Vent IndicatorMaintaining the Exhaust System Check Vent OperationKenmore Connect System Using the Kenmore Connect SystemProblem Possible Cause Solutions Before Calling for ServiceDry Before Calling for Service Problem Possible Cause SolutionsClothes are wrinkled Clothes are shrinkingSteam Features Not Display shows errorCode tE1 or tE2 Lint on clothes WorkingDisclaimer of implied warranties limitation of remedies Kenmore Elite Limited Warranty