Alliance Laundry Systems 907003062 manual Belt Drive

Page 51

Belt Drive

The drive assemblies consist of motors, belts, eyebolts and a step pulley.

The pulley diameters are sized to produce a cylinder speed of 37-39 RPM for 120 pound models or 29-31 RPM for 170 pound models.

The step pulley assembly is used for speed reduction as well as a means of adjusting belt tension. The pulley mounting plate is attached to the cabinet. The frame mounting plate has vertically slotted holes allowing up and down movement of the step pulley mounting plate for belt adjustment.

Adjust the belt tension as follows:

1.Disconnect electrical power to the tumble dryer before attempting any adjustments to the drive assembly.

2.Loosen pulley mounting plate bolts.

3.Loosen the upper nut on the final drive eyebolt.

4.Rotate the lower nut of the final drive eyebolt clockwise until proper belt tension is achieved.

Adjustments

5.Rotate upper nut clockwise against the lower nut in order to lock it into place.

6.Tighten pulley mounting plate bolts. Recheck belt tension.

7.If necessary, adjust the drive motor belt tension eyebolt using a similar procedure.

8.Adjust blower belt tension on 120 pound

50 Hertz tumble dryers and all 170 pound tumble dryers using a similar procedure.

NOTE: Proper tensions for new belts are

45-55 pounds for the motor belt, 55-65 pounds for the final drive, 60-65 pounds for 120 pound blower, and 75-80 pounds for 170 pound blower measured with a Borroughs Belt Tension Gauge. Using a Browning Belt Tension Gauge, the motor belt deflection should be 0.31 inch at five pounds pressure, and final drive belt deflection should be 0.25 inch at five pounds pressure.

Belts should not slip or make any noise when starting up under normal load.

70420801 (EN)

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

49

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Tumble Dryers Page What to do if YOU Smell GAS For Your Safety Contents Installing Steam Trap and Making Condensate Model Identification Customer ServiceWiring Diagram Location IntroductionSerial Plate Location IntroductionConversion Table Multiply To Obtain Safety Information Safety Information Important Safety InstructionsW055R1 Specifications and Dimensions Exhaust Outlet Dimensions and Locations Models 120L/N/E Pound Tumble Dryer Dimensions and Exhaust Outlet LocationsSpecifications and Dimensions Cabinet Dimensions Models 120L/N/EExhaust Outlet Dimensions and Locations Models 170L/N/S Cabinet Dimensions Models 170L/N/S170L/N Electric and Gas Connection Locations for Gas ModelsModels Electrical Connection Gas Connection 120L/NElectric and Steam Connection Locations for Steam Models 170SModels Electrical Connection 120S Models 120E Electric Connection Location for Electric ModelsMaterials Required Obtain locally All Models InstallationPre-Installation Inspection Location RequirementsInstallation Position and Level the Tumble Dryer Before Placing Tumble Dryer into ServiceRequired for CE Models Only General Information Installing CE Gas Drying Tumble DryersQuantity Pressure Orifice Code Mbar Supply Burner Country Gas Type Group OrificeBasic Configuration Specific Conversion Procedures How to Adjust Gas Valve Governor/Regulator Venting Exhaust RequirementsLayout Make-Up AirExhaust Requirements Alternate Venting for 120 Pound tumble dryersDuct Diameter Equivalent Length Rigid Straight Duct Individual VentingTMB2361N Duct Pound Stations Mm Duct ONE Manifold AssemblyTWO Manifold Assemblies Gas Requirements Gas Requirements .4 mm Gas Pipe Loop Gas Supply Pipe Sizing and Looping600,000 Sizes shown in inches mm 300,000400,000 500,000High Altitude Orifice Sizing Non-CE Models Altitude Orifice NewGas Rate Feet Inches Quantity Grounding Instructions Electrical RequirementsElectrical Requirements For CE Models OnlyGas Service/Ground LocationGround and Terminal Block Locations Non-CEElectric To Connect Electrical Service to the Tumble Dryer Ferrite Ring Installation Jumper Configuration InstructionsElectrical Requirements Piping Recommendations Steam RequirementsSteam Requirements Thermal Oil PrepPound Tumble Dryers Model Steam Pressure Minimum Steam Trap SizePounds Condensate/Hour 80-100 4 in. NPT 517 Based on maximum psi Gas Burner Air Shutter AdjustmentsLoading Door Strike Airflow SwitchLoading Door Switch AdjustmentsBelt Drive Removing Tumble Dryer from Service

907003062 specifications

Alliance Laundry Systems has long been recognized as a leader in the commercial laundry industry, providing innovative solutions that enhance operational efficiency and user experience. One of its standout offerings is the Alliance Laundry Systems model 907003062. This model is a robust piece of equipment designed for high-performance washing needs in a variety of commercial settings, from laundromats to hotel and institutional laundry facilities.

At the heart of the 907003062 is its powerful motor that ensures efficient and effective cleaning performance. The model features a high extraction speed, which not only reduces drying time but also helps to save energy. This efficiency is critical for high-volume operations looking to optimize workflow and reduce utility costs.

The design of the 907003062 prioritizes user-friendliness. It comes equipped with an intuitive control panel that allows operators to easily select washing cycles and settings. This feature significantly reduces the learning curve, enabling staff to become proficient quickly. Programmable settings allow businesses to customize wash programs to cater to various fabric types, ensuring garments receive the appropriate treatment without sacrificing cleanliness or quality.

Durability is another hallmark of the 907003062. Constructed with high-quality materials, this model is built to withstand the rigors of constant use in a busy commercial environment. The components are designed to resist wear and tear, ensuring longevity and reliability. This makes it a sound investment for businesses looking to avoid frequent maintenance or replacement costs.

Additionally, the 907003062 incorporates advanced technologies that promote water and energy conservation. This commitment to sustainability helps businesses reduce their environmental footprint while also appealing to the eco-conscious consumer. Features such as automatic water level adjustment and efficient detergent usage contribute to lowering operational costs.

In summary, the Alliance Laundry Systems 907003062 is a well-rounded commercial washing machine that excels in performance, durability, and efficiency. With its powerful motor, user-friendly controls, customized wash programs, and energy-saving technologies, it is an ideal solution for businesses seeking to enhance their laundry operations while maintaining high standards of cleanliness and sustainability. As commercial laundry needs evolve, models like the 907003062 set the benchmark for excellence in the industry.
Top Page Image Contents