Alliance Laundry Systems 907003062 manual Exhaust Requirements, Layout, Make-Up Air, Venting

Page 27

Exhaust Requirements

WARNING

A drying tumble dryer produces combustible lint. To reduce the risk of fire, the tumble dryer must be exhausted to the outdoors.

W057R1

To reduce the risk of fire and accumulation of combustible gases, DO NOT exhaust tumbler air into a window well, gas vent, chimney or enclosed, unventilated area such as an attic, ceiling, crawl space under a building, or concealed space of a building.

W506

Layout

Wherever possible, install tumble dryers along an outside wall, where duct length can be kept to a minimum and makeup air can be easily accessed. Construction must not block the airflow at the top rear of the tumble dryer. Doing so would prevent adequate air supply to the tumble dryer combustion chamber.

Make-Up Air

A tumble dryer is forced air exhausted and requires provisions for make-up air to replace air exhausted by tumble dryer. Refer to Table 3.

IMPORTANT: Do not obstruct flow of combustion and ventilation air.

Required Make-Up Air Opening

(to the outside) for Each Tumble Dryer

Models

 

Opening

 

 

 

 

120 Pound

 

360 in.2

(2323 cm2)

 

free air

 

 

 

 

 

 

170 Pound

 

525 in.2

(3710 cm2)

 

free air

 

 

 

 

 

 

 

Table 3

 

Make-up air openings with louvers will restrict air flow. The opening must be increased to compensate for area taken up by louvers.

Make-up air openings in rooms containing tumble dryer(s) and/or gas fired hot water heater or other gravity vented appliances must be increased sufficiently to prevent downdrafts in any of the vents when all tumble dryers are in operation. Do not locate gravity vented appliances between tumble dryer(s) and make-up air openings. If it is necessary to duct make- up air to tumble dryer(s), increase area of duct work by 25% to compensate for any restriction in air movement.

Venting

WARNING

To reduce the risk of fire due to increased static pressure, we do not recommend installation of in-line secondary lint filters or lint collectors. If secondary systems are mandated, frequently clean the system to assure safe operation.

W749

IMPORTANT: Installing in-line filters or lint collectors will cause increased static pressure. Failure to maintain the secondary lint system will decrease tumble dryer efficiency and may void machine warranty.

For maximum efficiency and minimum lint accumulation, tumble dryer must be exhausted to the outdoors by the shortest possible route.

Proper sized exhaust ducts are essential for proper operation. All elbows should be sweep type. Exhaust ducts must be assembled so the interior surfaces are smooth, so the joints do not permit the accumulation of lint. DO NOT use plastic, thin foil or Type B flexible ducts – rigid metal ducts are recommended. Use exhaust ducts made of sheet metal or other noncombustible material. Use of duct tape or pop- rivets on all seams and joints is recommended, if allowed by local codes.

Verify that old ducts are thoroughly cleaned before installing new tumble dryer(s).

70420801 (EN)

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

25

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Tumble Dryers Page What to do if YOU Smell GAS For Your Safety Contents Installing Steam Trap and Making Condensate Model Identification Customer ServiceWiring Diagram Location IntroductionSerial Plate Location IntroductionConversion Table Multiply To Obtain Safety Information Safety Information Important Safety InstructionsW055R1 Specifications and Dimensions Exhaust Outlet Dimensions and Locations Models 120L/N/E Pound Tumble Dryer Dimensions and Exhaust Outlet LocationsSpecifications and Dimensions Cabinet Dimensions Models 120L/N/EExhaust Outlet Dimensions and Locations Models 170L/N/S Cabinet Dimensions Models 170L/N/S170L/N Electric and Gas Connection Locations for Gas ModelsModels Electrical Connection Gas Connection 120L/NElectric and Steam Connection Locations for Steam Models 170SModels Electrical Connection 120S Models 120E Electric Connection Location for Electric ModelsMaterials Required Obtain locally All Models InstallationPre-Installation Inspection Location RequirementsInstallation Position and Level the Tumble Dryer Before Placing Tumble Dryer into ServiceRequired for CE Models Only General Information Installing CE Gas Drying Tumble DryersQuantity Pressure Orifice Code Mbar Supply Burner Country Gas Type Group OrificeBasic Configuration Specific Conversion Procedures How to Adjust Gas Valve Governor/Regulator Venting Exhaust RequirementsLayout Make-Up AirExhaust Requirements Alternate Venting for 120 Pound tumble dryersDuct Diameter Equivalent Length Rigid Straight Duct Individual VentingTMB2361N Duct Pound Stations Mm Duct ONE Manifold AssemblyTWO Manifold Assemblies Gas Requirements Gas Requirements .4 mm Gas Pipe Loop Gas Supply Pipe Sizing and Looping600,000 Sizes shown in inches mm 300,000400,000 500,000High Altitude Orifice Sizing Non-CE Models Altitude Orifice NewGas Rate Feet Inches Quantity Grounding Instructions Electrical RequirementsElectrical Requirements For CE Models OnlyGas Service/Ground LocationGround and Terminal Block Locations Non-CEElectric To Connect Electrical Service to the Tumble Dryer Ferrite Ring Installation Jumper Configuration InstructionsElectrical Requirements Piping Recommendations Steam RequirementsSteam Requirements Thermal Oil PrepPound Tumble Dryers Model Steam Pressure Minimum Steam Trap SizePounds Condensate/Hour 80-100 4 in. NPT 517 Based on maximum psi Gas Burner Air Shutter AdjustmentsLoading Door Strike Airflow SwitchLoading Door Switch AdjustmentsBelt Drive Removing Tumble Dryer from Service

907003062 specifications

Alliance Laundry Systems has long been recognized as a leader in the commercial laundry industry, providing innovative solutions that enhance operational efficiency and user experience. One of its standout offerings is the Alliance Laundry Systems model 907003062. This model is a robust piece of equipment designed for high-performance washing needs in a variety of commercial settings, from laundromats to hotel and institutional laundry facilities.

At the heart of the 907003062 is its powerful motor that ensures efficient and effective cleaning performance. The model features a high extraction speed, which not only reduces drying time but also helps to save energy. This efficiency is critical for high-volume operations looking to optimize workflow and reduce utility costs.

The design of the 907003062 prioritizes user-friendliness. It comes equipped with an intuitive control panel that allows operators to easily select washing cycles and settings. This feature significantly reduces the learning curve, enabling staff to become proficient quickly. Programmable settings allow businesses to customize wash programs to cater to various fabric types, ensuring garments receive the appropriate treatment without sacrificing cleanliness or quality.

Durability is another hallmark of the 907003062. Constructed with high-quality materials, this model is built to withstand the rigors of constant use in a busy commercial environment. The components are designed to resist wear and tear, ensuring longevity and reliability. This makes it a sound investment for businesses looking to avoid frequent maintenance or replacement costs.

Additionally, the 907003062 incorporates advanced technologies that promote water and energy conservation. This commitment to sustainability helps businesses reduce their environmental footprint while also appealing to the eco-conscious consumer. Features such as automatic water level adjustment and efficient detergent usage contribute to lowering operational costs.

In summary, the Alliance Laundry Systems 907003062 is a well-rounded commercial washing machine that excels in performance, durability, and efficiency. With its powerful motor, user-friendly controls, customized wash programs, and energy-saving technologies, it is an ideal solution for businesses seeking to enhance their laundry operations while maintaining high standards of cleanliness and sustainability. As commercial laundry needs evolve, models like the 907003062 set the benchmark for excellence in the industry.
Top Page Image Contents