Parts List for Figure, KEY Description Quan

Page 51

RYOBI 10 in. (254 mm) TABLE SAW – MODEL NO. BT3100

The model number will be found on the data plate attached to the right side panel of the cabinet, next to the saw’s on board receptacle. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts.

		PARTS LIST FOR FIGURE 64
KEY
NO.	DESCRIPTION	QUAN.
1	Leveling Foot	4
2	Hex Nut	32
3	Washer	32
4	Carriage Bolt	24
5	Leg	4
6	Upper Brace	2
7	Screw	4
8	Hex Nut	8
9	Upper Side Brace	2
10	Lower Leg Brace	4
11	Storage Bracket	4
12	Washer	12
13	Bolt	4
	Stand Fastener Package	1
	Operator’s Manual

Page 51

Image 51

Ryobi BT3100 manual Parts List for Figure, KEY Description Quan

Contents

Save this Manual for Future Reference Operators Manual Product Specifications Table of Contents Rules for Safe Operation Symbol Meaning Safety Alert Symbol Read ALL Instructions Blades Coast After Turn OFF Before Making a CUT, be Sure ALL Adjustments are Secure No Hands Symbol Safety and International Symbols Grounding Instructions ElectricalExtension Cords Electrical Connection Glossary of Terms Socket Wrench UnpackingTools Needed In. NUT Driver Key Description Quan Loose Parts List E J Following items are included with your table saw leg stand Scale FeaturesGetting to Know Your SAW Sliding Operating Components Power Switch LASER-CUT Body Expansion Slots Blade Rotation Speed and WiringBlades Precision Ground MICRO-GRAIN Carbide Teeth Assembling LEG Stand Assembly To Install Front and Back Rails Assembling Storage BracketsMounting the LEG Stand on the Table SAW Base Hole B To Install Miter Table and FenceRear Rail END Plug Holder NUT Miter Handwheel FIT LIP of Table Into Rear Rail To Install Accessory Table and RIP FenceREMOVING/REPLACING the Throat Plate Lever Throat Plate To Check SAW Blade InstallationTo Install Blade Guard Assembly Small HEX Wrench Replacing the Throat Plate Screws Operation Types of Cuts HOW to Make a Featherboard HOW to Mount a FeatherboardFeatherboard To Remove the Blade Riving Knife Mounting Plate HEX Nuts Shims Blade Guard Riving KnifeRiving Knife Blade Inch To Adjust the Blade Depth To Adjust the Blade AngleTo SET the Scale to the Blade Miter Slide Lock Slots for Locking Miter Table Adjustingmiter Clampfence Quick StopTo Lock Miter Table To Make a Straight Cross CUT Miter Table Blade Rear Rail RIP Fence Adjusting ClampTo Make a Miter CUT To Make a Straight RIP CUT To Make a Bevel RIP CUT To Make a Bevel Cross CUT Accessory Miter Locking Clamps Rail Clamp To Make a Compound Miter CUTTo Make a Large Panel CUT To Make NON-THROUGH Cuts FeatherboardClamp Push Block Bevel To Make Dado Cuts Lubrication MaintenanceGeneral Maintenance Backup Washer Stop Bolt Lock To SET Blade AT 0 orTo Check the Alignment of the RIP Fence to the Blade Screws Lock NUT Screw SET Front Rail Miter Locking Clamp To Adjust the Bevel Locking LeverTo Align the Miter Locking Clamps SET Screw Lobe Socket Head Screw HEX NUT TAB CAM Spring Spring Plate Backup HEX NUT To Adjust the Front and Rear Rail ClampsTo Adjust the Accessory Table To Adjust the Sliding Miter Table Assembly To Check Miter Base Parallelism Checking Sliding Miter Table Assembly Eight screws are visible on the miter base B Making Adjustments to Sliding Miter Table Assembly LIP of Base To Adjust the Miter FenceTo Adjust QUICK-STOP Miter Indicator Problem Cause Solution Trouble Shooting Center Ryobi Authorized ServicePage Refer to Figure 7672 112 101 110 104 122 103 111 102 105 107 108 113115 116 117 119 118 121 120 109 See Back page for Ordering Instructions Parts List Figure Parts List Contd Sliding Miter Table Assembly RIP Fence Assembly Motor Assembly 506 500 501 504 502 503 505 Key Description Quan Blade Guard Assembly Ryobi 10 in mm Table SAW Model NO. BT3100 KEY Description Quan Parts List for Figure Ryobi TECHNOLOGIES, INC Operators Manual 10 in mm Table Saw Model BT3100

RYOBI 10 in. (254 mm) TABLE SAW – MODEL NO. BT3100

PARTS LIST FOR FIGURE 64

KEY

DESCRIPTION

QUAN.