Riving Knife for Ryobi Table Saw - BT3100 Parts & Manual

OPERATION

TO CHECK, REPLACE OR ADJUST THE RIVING KNIFE AND BLADE GUARD ASSEMBLY

The riving knife is mounted between several shims that can be relocated as needed to center the knife behind the blade. It is held in place by two bolts and hex nuts at its base. The bolts are set in slots that permit front-to-back adjustment.

WARNING:

Unplug the saw before working on it. If the saw is not unplugged, accidental start-up can occur, resulting in possible serious injury.

■Remove the throat plate.

■With blade guard up, make sure the riving knife is placed at least 1/8 in. from the outer points of the blade. See Figure 29. Then make sure it is centered within the width of the blade. See Figure 30. If either placement is wrong, adjust with the following steps.

■Raise the saw blade by pushing the bevel locking lever to the left and rotating the blade adjustment handle clockwise.

■Put the saw in angle mode by moving the bevel locking lever to the right. Slowly turn the blade adjusting handle until the bevel indicator is at a 30˚ angle. Lock the angle by holding the blade adjusting handle with one hand and returning the bevel locking lever to the left with the other.

■With the box end of the small hex key, remove the two nuts at the base of the riving knife. Remove the riving knife/guard assembly.

■Rearrange the riving knife between the shims to achieve the correct centering.

WARNING:

Properly align riving knife. Improperly aligned riving knife can cause blade to bind which will increase risk of kickback.

■Adjust the bolts front-to-back as needed to place the riving knife approximately 1/8 in. from the blade’s outer points. Put the nuts back on and tighten.

■Bring the blade back to the desired angle and height. Insert the throat plate, lower the blade, and secure the throat plate with the throat plate screw. Tighten the screw firmly.

BLADE

GUARD

RIVING KNIFE

BLADE

THROAT PLATE

Fig. 28

RIVING KNIFE

BLADE

1/8 INCH

Fig. 29

RIVING

KNIFE

MOUNTING

PLATE

HEX NUTS	SHIMS
	Fig. 30

Page 25

Image 25

Ryobi BT3100 manual Blade Guard Riving Knife, Riving Knife Blade, Inch, Riving Knife Mounting Plate HEX Nuts Shims

Contents

Save this Manual for Future Reference Operators Manual Product Specifications Table of Contents Rules for Safe Operation Symbol Meaning Safety Alert Symbol Read ALL Instructions Blades Coast After Turn OFF Before Making a CUT, be Sure ALL Adjustments are Secure No Hands Symbol Safety and International Symbols Extension Cords ElectricalElectrical Connection Grounding Instructions Glossary of Terms Tools Needed UnpackingIn. NUT Driver Socket Wrench Key Description Quan Loose Parts List E J Following items are included with your table saw leg stand Getting to Know Your SAW FeaturesSliding Scale Operating Components Power Switch Blades Speed and WiringPrecision Ground MICRO-GRAIN Carbide Teeth LASER-CUT Body Expansion Slots Blade Rotation Assembling LEG Stand Assembly Assembling Storage Brackets To Install Front and Back RailsMounting the LEG Stand on the Table SAW Base Rear Rail END Plug Holder NUT Miter To Install Miter Table and FenceHandwheel Hole B REMOVING/REPLACING the Throat Plate To Install Accessory Table and RIP FenceLever FIT LIP of Table Into Rear Rail To Install Blade Guard Assembly To Check SAW Blade InstallationSmall HEX Wrench Throat Plate Replacing the Throat Plate Screws Operation Types of Cuts HOW to Mount a Featherboard HOW to Make a FeatherboardFeatherboard To Remove the Blade Riving Knife Blade Blade Guard Riving KnifeInch Riving Knife Mounting Plate HEX Nuts Shims To Adjust the Blade Angle To Adjust the Blade DepthTo SET the Scale to the Blade To Lock Miter Table Adjustingmiter Clampfence Quick StopTo Make a Straight Cross CUT Miter Slide Lock Slots for Locking Miter Table To Make a Miter CUT Adjusting ClampTo Make a Straight RIP CUT Miter Table Blade Rear Rail RIP Fence To Make a Bevel RIP CUT To Make a Bevel Cross CUT To Make a Compound Miter CUT Accessory Miter Locking Clamps Rail ClampTo Make a Large Panel CUT Featherboard To Make NON-THROUGH CutsClamp Push Block Bevel To Make Dado Cuts General Maintenance MaintenanceBackup Washer Lubrication To Check the Alignment of the RIP Fence to the Blade To SET Blade AT 0 orScrews Lock NUT Stop Bolt Lock To Align the Miter Locking Clamps To Adjust the Bevel Locking LeverSET Screw Lobe Socket Head Screw HEX NUT TAB CAM Spring Screw SET Front Rail Miter Locking Clamp To Adjust the Accessory Table To Adjust the Front and Rear Rail ClampsTo Adjust the Sliding Miter Table Assembly Spring Plate Backup HEX NUT To Check Miter Base Parallelism Checking Sliding Miter Table Assembly Eight screws are visible on the miter base B Making Adjustments to Sliding Miter Table Assembly To Adjust QUICK-STOP To Adjust the Miter FenceMiter Indicator LIP of Base Problem Cause Solution Trouble Shooting Center Ryobi Authorized ServicePage 7672 112 101 110 104 122 103 111 102 105 107 108 113 Refer to Figure115 116 117 119 118 121 120 109 See Back page for Ordering Instructions Parts List Figure Parts List Contd Sliding Miter Table Assembly RIP Fence Assembly Motor Assembly 506 500 501 504 502 503 505 Key Description Quan Blade Guard Assembly Ryobi 10 in mm Table SAW Model NO. BT3100 KEY Description Quan Parts List for Figure Ryobi TECHNOLOGIES, INC Operators Manual 10 in mm Table Saw Model BT3100