Alliance Laundry Systems 907003062 manual Adjustments, Gas Burner Air Shutter

Page 49

Adjustments

WARNING

To reduce the risk of electric shock, fire, explosion, serious injury or death:

•Disconnect electric power to the tumble dryer before servicing.

•Close gas shut-off valve to gas tumble dryer before servicing.

•Close steam valve to steam tumble dryer before servicing.

•Never start the tumble dryer with any guards/panels removed.

•Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the tumble dryer is properly grounded.

W002R1

Gas Burner Air Shutter

NOTE: Air inlet shutters on the burner must be adjusted so sufficient air is metered into the system for proper combustion and maximum efficiency. Before adjusting the inlet shutters, be sure that all lint is removed from lint compartments and lint screen.

Air shutter adjustment will vary from location to location and will depend on the vent system, number of units installed, make-up air and line gas pressure. Opening the shutter increases the amount of primary air supplied to the burner, while closing the shutter decreases the primary air supply. Adjust air shutter as follows:

Refer to Figure 16.

1.Remove the upper access panel and burner inspection hole plate.

2.Start the tumble dryer and check the flame pattern. If the flame pattern is straight up, insufficient air is flowing through the tumble dryer. A flame pattern that flares to the right and left indicates no air is flowing through the tumble dryer. Correct air and gas mixture is indicated if the flame pattern is primarily blue, with small yellow tips, and bends to the left of the heater section. Too little air is indicated if the flame is yellow, lazy and smoky.

3.To adjust the air shutter, loosen air inlet shutter adjusting screw.

4.Open or close air shutter as necessary to obtain proper flame intensity.

5.After air shutter is adjusted for proper flame, tighten air shutter adjusting screw securely.

 

PROPER AIRFLOW

 

1

 

INSUFFICIENT AIRFLOW

 

1

 

NO AIRFLOW

 

1

 

T464I

1

Air Shutter Adjusting Screw

Figure 16

70420801 (EN)

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

47

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Tumble Dryers Page What to do if YOU Smell GAS For Your Safety Contents Installing Steam Trap and Making Condensate Wiring Diagram Location Customer ServiceIntroduction Model IdentificationIntroduction Serial Plate LocationConversion Table Multiply To Obtain Safety Information Safety Information Important Safety InstructionsW055R1 Specifications and Dimensions Specifications and Dimensions Pound Tumble Dryer Dimensions and Exhaust Outlet LocationsCabinet Dimensions Models 120L/N/E Exhaust Outlet Dimensions and Locations Models 120L/N/EExhaust Outlet Dimensions and Locations Models 170L/N/S Cabinet Dimensions Models 170L/N/SModels Electrical Connection Gas Connection Electric and Gas Connection Locations for Gas Models120L/N 170L/N170S Electric and Steam Connection Locations for Steam ModelsModels Electrical Connection 120S Models 120E Electric Connection Location for Electric ModelsPre-Installation Inspection InstallationLocation Requirements Materials Required Obtain locally All ModelsInstallation Position and Level the Tumble Dryer Before Placing Tumble Dryer into ServiceRequired for CE Models Only General Information Installing CE Gas Drying Tumble DryersQuantity Pressure Orifice Code Mbar Supply Burner Country Gas Type Group OrificeBasic Configuration Specific Conversion Procedures How to Adjust Gas Valve Governor/Regulator Layout Exhaust RequirementsMake-Up Air VentingExhaust Requirements Alternate Venting for 120 Pound tumble dryersDuct Diameter Equivalent Length Rigid Straight Duct Individual VentingTMB2361N Duct Pound Stations Mm Duct ONE Manifold AssemblyTWO Manifold Assemblies Gas Requirements Gas Requirements .4 mm Gas Pipe Loop Gas Supply Pipe Sizing and Looping400,000 Sizes shown in inches mm 300,000500,000 600,000Non-CE Models Altitude Orifice New High Altitude Orifice SizingGas Rate Feet Inches Quantity Grounding Instructions Electrical RequirementsElectrical Requirements For CE Models OnlyGround and Terminal Block Locations Service/Ground LocationNon-CE GasElectric To Connect Electrical Service to the Tumble Dryer Ferrite Ring Installation Jumper Configuration InstructionsElectrical Requirements Piping Recommendations Steam RequirementsSteam Requirements Thermal Oil PrepModel Steam Pressure Minimum Steam Trap Size Pound Tumble DryersPounds Condensate/Hour 80-100 4 in. NPT 517 Based on maximum psi Gas Burner Air Shutter AdjustmentsLoading Door Switch Airflow SwitchAdjustments Loading Door StrikeBelt Drive Removing Tumble Dryer from Service

907003062 specifications

Alliance Laundry Systems has long been recognized as a leader in the commercial laundry industry, providing innovative solutions that enhance operational efficiency and user experience. One of its standout offerings is the Alliance Laundry Systems model 907003062. This model is a robust piece of equipment designed for high-performance washing needs in a variety of commercial settings, from laundromats to hotel and institutional laundry facilities.

At the heart of the 907003062 is its powerful motor that ensures efficient and effective cleaning performance. The model features a high extraction speed, which not only reduces drying time but also helps to save energy. This efficiency is critical for high-volume operations looking to optimize workflow and reduce utility costs.

The design of the 907003062 prioritizes user-friendliness. It comes equipped with an intuitive control panel that allows operators to easily select washing cycles and settings. This feature significantly reduces the learning curve, enabling staff to become proficient quickly. Programmable settings allow businesses to customize wash programs to cater to various fabric types, ensuring garments receive the appropriate treatment without sacrificing cleanliness or quality.

Durability is another hallmark of the 907003062. Constructed with high-quality materials, this model is built to withstand the rigors of constant use in a busy commercial environment. The components are designed to resist wear and tear, ensuring longevity and reliability. This makes it a sound investment for businesses looking to avoid frequent maintenance or replacement costs.

Additionally, the 907003062 incorporates advanced technologies that promote water and energy conservation. This commitment to sustainability helps businesses reduce their environmental footprint while also appealing to the eco-conscious consumer. Features such as automatic water level adjustment and efficient detergent usage contribute to lowering operational costs.

In summary, the Alliance Laundry Systems 907003062 is a well-rounded commercial washing machine that excels in performance, durability, and efficiency. With its powerful motor, user-friendly controls, customized wash programs, and energy-saving technologies, it is an ideal solution for businesses seeking to enhance their laundry operations while maintaining high standards of cleanliness and sustainability. As commercial laundry needs evolve, models like the 907003062 set the benchmark for excellence in the industry.
Top Page Image Contents