Alliance Laundry Systems 907003062 Jumper Configuration Instructions, Ferrite Ring Installation

Page 43

Jumper Configuration Instructions

Changing the transformer configuration jumper is required, PRIOR TO SUPPLYING POWER TO THE MACHINE, if any of the following apply:

IMPORTANT: Failure to install the proper configuration jumper may result in damage to sensitive electronic controls and may void warranty.

∙Location Voltage 200 – 208 Volt service and are connecting a model rated for 240 Volt operation.

Replace the 240 Volt jumper with the 208 Volt jumper per the conversion label, located on the rear of the tumble dryer, sign and date conversion label to document the conversion.

∙You have 400 – 415 Volt service and are connecting a model rated for 380 Volt operation.

Electrical Requirements

Ferrite Ring Installation

Models with RM Control Suffix Only

The ferrite ring provided in the literature packet must be installed over the power leads during connection of electrical service. The ferrite protects the sensitive electronic controls from destructive electrical disturbances which may be present on power lines to the machine. Failure to properly install the ferrite ring may result in damage to the electronic controls and will void control warranty.

To Install:

1.Immediately after connection of power leads and before applying power to machine, locate each of the incoming service leads including ground.

2.Snap the ferrite ring closed over all the service leads inside of the contactor box as shown. It is important that the ferrite ring be installed inside the contactor box. Refer to Figure 13. Do not install the ferrite outside of the box or other area. Make sure that service leads are in the center of the ferrite before closing the ring so not to pinch or damage leads.

 

Non-CE Models

 

CE Models

 

 

 

3

1

 

 

 

 

1

 

 

 

2

 

2

 

TMB2270N

 

TMB2271N

1

Ferrite Ring

3

Models Through 7/31/11

2

Junction Box

 

 

Figure 13

70420801 (EN)

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

41

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Tumble Dryers Page What to do if YOU Smell GAS For Your Safety Contents Installing Steam Trap and Making Condensate Model Identification Customer ServiceWiring Diagram Location IntroductionIntroduction Serial Plate LocationConversion Table Multiply To Obtain Safety Information Safety Information Important Safety InstructionsW055R1 Specifications and Dimensions Exhaust Outlet Dimensions and Locations Models 120L/N/E Pound Tumble Dryer Dimensions and Exhaust Outlet LocationsSpecifications and Dimensions Cabinet Dimensions Models 120L/N/EExhaust Outlet Dimensions and Locations Models 170L/N/S Cabinet Dimensions Models 170L/N/S170L/N Electric and Gas Connection Locations for Gas ModelsModels Electrical Connection Gas Connection 120L/N170S Electric and Steam Connection Locations for Steam ModelsModels Electrical Connection 120S Models 120E Electric Connection Location for Electric ModelsMaterials Required Obtain locally All Models InstallationPre-Installation Inspection Location RequirementsInstallation Position and Level the Tumble Dryer Before Placing Tumble Dryer into ServiceRequired for CE Models Only General Information Installing CE Gas Drying Tumble DryersQuantity Pressure Orifice Code Mbar Supply Burner Country Gas Type Group OrificeBasic Configuration Specific Conversion Procedures How to Adjust Gas Valve Governor/Regulator Venting Exhaust RequirementsLayout Make-Up AirExhaust Requirements Alternate Venting for 120 Pound tumble dryersDuct Diameter Equivalent Length Rigid Straight Duct Individual VentingTMB2361N Duct Pound Stations Mm Duct ONE Manifold AssemblyTWO Manifold Assemblies Gas Requirements Gas Requirements .4 mm Gas Pipe Loop Gas Supply Pipe Sizing and Looping600,000 Sizes shown in inches mm 300,000400,000 500,000Non-CE Models Altitude Orifice New High Altitude Orifice SizingGas Rate Feet Inches Quantity Grounding Instructions Electrical RequirementsElectrical Requirements For CE Models OnlyGas Service/Ground LocationGround and Terminal Block Locations Non-CEElectric To Connect Electrical Service to the Tumble Dryer Ferrite Ring Installation Jumper Configuration InstructionsElectrical Requirements Piping Recommendations Steam RequirementsSteam Requirements Thermal Oil PrepModel Steam Pressure Minimum Steam Trap Size Pound Tumble DryersPounds Condensate/Hour 80-100 4 in. NPT 517 Based on maximum psi Gas Burner Air Shutter AdjustmentsLoading Door Strike Airflow SwitchLoading Door Switch AdjustmentsBelt Drive Removing Tumble Dryer from Service

907003062 specifications

Alliance Laundry Systems has long been recognized as a leader in the commercial laundry industry, providing innovative solutions that enhance operational efficiency and user experience. One of its standout offerings is the Alliance Laundry Systems model 907003062. This model is a robust piece of equipment designed for high-performance washing needs in a variety of commercial settings, from laundromats to hotel and institutional laundry facilities.

At the heart of the 907003062 is its powerful motor that ensures efficient and effective cleaning performance. The model features a high extraction speed, which not only reduces drying time but also helps to save energy. This efficiency is critical for high-volume operations looking to optimize workflow and reduce utility costs.

The design of the 907003062 prioritizes user-friendliness. It comes equipped with an intuitive control panel that allows operators to easily select washing cycles and settings. This feature significantly reduces the learning curve, enabling staff to become proficient quickly. Programmable settings allow businesses to customize wash programs to cater to various fabric types, ensuring garments receive the appropriate treatment without sacrificing cleanliness or quality.

Durability is another hallmark of the 907003062. Constructed with high-quality materials, this model is built to withstand the rigors of constant use in a busy commercial environment. The components are designed to resist wear and tear, ensuring longevity and reliability. This makes it a sound investment for businesses looking to avoid frequent maintenance or replacement costs.

Additionally, the 907003062 incorporates advanced technologies that promote water and energy conservation. This commitment to sustainability helps businesses reduce their environmental footprint while also appealing to the eco-conscious consumer. Features such as automatic water level adjustment and efficient detergent usage contribute to lowering operational costs.

In summary, the Alliance Laundry Systems 907003062 is a well-rounded commercial washing machine that excels in performance, durability, and efficiency. With its powerful motor, user-friendly controls, customized wash programs, and energy-saving technologies, it is an ideal solution for businesses seeking to enhance their laundry operations while maintaining high standards of cleanliness and sustainability. As commercial laundry needs evolve, models like the 907003062 set the benchmark for excellence in the industry.
Top Page Image Contents