ADC AD-360X2 manual Sail Switch Assembly, To Replace Sail Switch, To Adjust Sail Switch

Page 28

E. SAIL SWITCH ASSEMBLY

The sail switch is a heat circuit safety device, which controls the heat circuit only. When the dryer is operating and there is proper airflow, the sail switch damper pulls in and closes the sail switch, providing ALL the other heat related circuits are functioning properly. If an improper airflow occurs, the sail switch damper will release, and the circuit will open.

IMPORTANT: UNDER NO CIRCUMSTANCES should heat circuit safety devices ever be disabled.

TO REPLACE SAIL SWITCH

1.Discontinue power to the dryer.

2.Remove the two (2) screws, which hold the sail switch to the bracket.

NOTE: Be careful not to drop or lose the twin speed nut on the backside of the sail switch.

3. Disconnect the two (2) connectors on the sail switch.

4. Reverse this procedure for installing new sail switch. Adjust sail switch as described in the next section.

TO ADJUST SAIL SWITCH

1. Operate the installed dryer normally to verify that the heat system is fully operational.

2. Open the main dryer door.

3. Manually depress the door switch actuator.

4.While continuing to depress the door switch actuator, and with the door open, start the dryer.

5.If the heat system is not activated in 15-seconds, the sail switch is properly adjusted.

6.If the heat system is activated, the sail switch is improperly adjusted and must be readjusted by bending the actuator arm of the sail switch toward the left side of the dryer. If the actuator arm is bent too far toward the left side of the dryer, the dryer may not have heat when needed. After any adjustments of the sail switch, the above procedure must be repeated to verify proper operation.

CAUTION: DO NOT disable this switch by taping or screwing sail switch damper to burner. Personal injury or fire could result.

24

Page 27 Page 29
Image 28
Page 27 Page 29
Contents AD-360X2 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Data Label Information Safety Precautions Important InformationCleaning Routine MaintenanceSuggested Interval Adjustments AS RequiredInstallation Requirements ENCLOSURE, AIR SUPPLY, and Exhaust RequirementsElectrical and GAS Requirements Electrical RequirementsOperational Service Check Procedure Description of Parts Control PanelControl and Relay Panels Coin BOXDoor Switch Hinge Block Microprocessor AssemblyBasket Tumbler and Drive Motor Assembly Arrangement Basket TumblerTemperature Sensors Idler ARM and Impellor Mount AssemblyDrive Motor and Idler Pulley Arrangement GAS Burner Sail SwitchHI-LIMIT Thermostat Front Thruster Wheel Bracket Assembly Lint Drawer SwitchLint Drawer Rotational Sensor Assembly Rear Basket Tumbler Drive WheelsService IntroductionControls Computer To Replace ComputerTo Replace Keyboard Touch PAD To Replace Coin AcceptorTo Replace GAS Valve To Replace the Ignitor Probe Burner Controls GAS To Test and Adjust GAS Water Column W.C. Pressure To Convert from Natural to Liquid Propane L.P. GAS To Replace Direct Spark Ignition DSI Module Thermostats and Temperature SensorTo Replace HI-LIMIT Thermostat To Remove the Temperature Sensor or High Heat Protector To Replace Sail Switch Sail Switch AssemblyTo Adjust Sail Switch To Replace Main Door Switch To Install NEW Main Door GlassFront Panel and Main Door Assemblies To Replace Main Door Hinge BlocksTo Replace Front Panel To Replace the Nylon CatchTo Replace Rotational Sensor Switch Basket Tumbler Removal Basket Tumbler Wheel RemovalBCD-1 Type Module General System InformationVAC Transformer Page 760 Direct Spark Ignition DSI Flowchart Lockout Until power is removed From controlTroubleshooting Test EquipmentDSI Ignitor GAP Feeler Gauge 1/8 Page Page First Visual Check Second Visual Check Third Visual Check For Leaks Withaflame Blink Green Continuously Continuously Page For 120 VAC application only ADC PN 128927 5N7 Redundant GAS Valve Direct Spark Ignition DSI System Components Phase 5 Coin System Diagnosis TroubleshootingDiagnostics L.E.D. Display Failure Codes Page D. Display Indicators No Heat Condition Blower is on Page No Start Condition No Display Condition 115 VACDSFL Display Condition DOOr Display Condition Data Label Information Data LabelUsing a Manometer HOW to USE a Manometer ADC PNLight Emitting Diode L.E.D. Display Codes Page Page ADC450213 1 08/18/03-25
Related manuals
Manual 38 pages 18.19 Kb

AD-360X2 specifications

The ADC AD-360X2 is a high-performance audio component designed for audiophiles and professionals who demand quality and reliability. This digital-to-analog converter (DAC) is engineered to deliver superior sound quality, with an emphasis on precision and clarity.

One of the standout features of the AD-360X2 is its dual DAC architecture, which utilizes two high-end digital-to-analog chips to ensure a pristine audio output. This design not only enhances the audio resolution but also minimizes noise and distortion, resulting in a richer listening experience. The device supports high-resolution formats, including DSD and PCM, enabling users to enjoy their music in the highest quality available.

The AD-360X2 also boasts a wide range of connectivity options, allowing it to interface seamlessly with various audio devices. It includes USB, optical, and coaxial inputs, making it compatible with computers, CD players, and digital media players. This versatility means that users can easily integrate the AD-360X2 into their existing audio setup, enhancing their overall experience.

Another impressive characteristic of the AD-360X2 is its built-in headphone amplifier. This feature allows users to connect their headphones directly to the unit, providing an optimized listening experience without the need for additional equipment. The headphone amplifier is designed to drive a wide range of headphone impedances, ensuring compatibility with everything from high-impedance studio headphones to more consumer-oriented options.

Additionally, the AD-360X2 integrates advanced clock technology to enhance timing accuracy. The precision clock circuit works to reduce jitter, which is often a major source of distortion in digital audio systems. By ensuring that the signal is processed with impeccable timing, the device further elevates audio quality.

User-friendliness is another significant aspect of the AD-360X2. The device features a straightforward control interface, with an easy-to-read display that provides real-time information about the audio being played. This simplicity ensures that both novices and seasoned audio enthusiasts can operate the device with ease.

In conclusion, the ADC AD-360X2 is an exemplary digital-to-analog converter that combines high-end audio performance with user-friendly features. Its dual DAC architecture, extensive connectivity options, built-in headphone amplifier, and advanced clock technology make it a standout choice for anyone seeking to elevate their audio experience. Whether for personal use or professional applications, the AD-360X2 is engineered to meet and exceed the expectations of discerning audio lovers.
Top Page Image Contents