ADC AD-360X2 manual

Page 52

IMPORTANT: The Phase 5 coin microprocessor controller (computer) has its own internal heat sensing circuit fuse protection, located on the back side of the controller. If a “dSFL” condition occurs, check to see if this fuse has blown. If it has, DO NOT replace the entire microprocessor controller (computer); replace the fuse and do so with a 1/8-amp (Slo-Blo) fuse only.

NOTE: Once the microprocessor controller (computer) detects a problem in the heat circuit, it updates every 30-seconds. If the problem was a loose connection in this circuit, which corrected itself, the “dSFL” condition would be cancelled.

3.“SEFL” - indicates rotational sensor circuit failure meaning that there is a fault somewhere in the basket (tumbler) rotation detection circuit, or the Phase 5 coin microprocessor controller (computer) program related to this circuit (PL 0.l) is set incorrectly in the active mode (SEn) where the dryer is not equipped with the optional rotational sensor and should be set in the nonactive mode (nSEn). Also check to see if the belt came loose, or the rotational sensor magnet is broken. If not, adjust rotational sensor reed switch within 1/4” to the magnet.

4.“Hot” - indicates a possible overheating condition. The Phase 5 coin microprocessor controller (computer) monitors the temperature in the dryer at ALL times. If the microprocessor controller (computer) detects that the temperature in the dryer has exceeded 220° F (104° C), it will disable ALL outputs (shut the dryer down), the tone (bUZ) will sound for approximately 5-seconds, and the light emitting diode (L.E.D.) temperature sensor has dropped to 220° F (104° C) or lower and the microprocessor controller (computer) is manually reset by closing and opening the program switch (PS) on the back side of the controller.

MICROPROCESSOR CONTROLLER (COMPUTER) RELAY OUTPUT L.E.D. INDICATORS

There are three (3) L.E.D. indicators (red lights) located at the lower backside area of the controller, they are identified and labeled “dOOr,” “MOTOR,” and “HEAT” (as shown in the illustration on the next page). These L.E.D.s indicate that the outputs of the Phase 5 coin microprocessor controller (computer) or, in the case of the door switch, the input is functioning.

1.“dOOr” L.E.D. indicator should be on ALL the time (even if the dryer is not running) unless the main

door is open or there is a problem (open circuit) in the main door switch circuit.

2.“MOTOR” Output L.E.D. Indicator - if the dryer is started and the motor is not operating, yet both the microprocessor controller (computer) display motor indicator dot and the “dOOr” input L.E.D. indicator are on, but the motor output L.E.D. indicator is off, then the fault is in the Phase 5 coin microprocessor controller (computer) itself. If the motor is not operating and the MOTOR output indicator is on, then the problem is elsewhere (i.e., external of the microprocessor controller [computer]).

3.“HEAT” Output L.E.D. Indicator - If the dryer is started and there is no “heat,” yet the microprocessor controller (computer) display heat circuit indicator dot is on, but the output L.E.D. indicator is off, then the fault is in the Phase 5 coin microprocessor controller (computer) itself. If both the display heat indicator dot and the heat output L.E.D. indicator are on, then the problem is elsewhere (i.e., external of the microprocessor controller [computer]).

48

Page 51 Page 53
Image 52
Page 51 Page 53
Contents AD-360X2 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Data Label Information Safety Precautions Important InformationCleaning Routine MaintenanceSuggested Interval Adjustments AS RequiredInstallation Requirements ENCLOSURE, AIR SUPPLY, and Exhaust RequirementsElectrical and GAS Requirements Electrical RequirementsOperational Service Check Procedure Description of Parts Control PanelControl and Relay Panels Coin BOXDoor Switch Hinge Block Microprocessor AssemblyBasket Tumbler and Drive Motor Assembly Arrangement Basket TumblerTemperature Sensors Idler ARM and Impellor Mount AssemblyDrive Motor and Idler Pulley Arrangement GAS Burner Sail SwitchHI-LIMIT Thermostat Front Thruster Wheel Bracket Assembly Lint Drawer SwitchLint Drawer Rotational Sensor Assembly Rear Basket Tumbler Drive WheelsService IntroductionControls Computer To Replace ComputerTo Replace Keyboard Touch PAD To Replace Coin AcceptorTo Replace GAS Valve To Replace the Ignitor Probe Burner Controls GAS To Test and Adjust GAS Water Column W.C. Pressure To Convert from Natural to Liquid Propane L.P. GAS To Replace Direct Spark Ignition DSI Module Thermostats and Temperature SensorTo Replace HI-LIMIT Thermostat To Remove the Temperature Sensor or High Heat Protector To Replace Sail Switch Sail Switch AssemblyTo Adjust Sail Switch To Replace Main Door Switch To Install NEW Main Door GlassFront Panel and Main Door Assemblies To Replace Main Door Hinge BlocksTo Replace Front Panel To Replace the Nylon CatchTo Replace Rotational Sensor Switch Basket Tumbler Removal Basket Tumbler Wheel RemovalBCD-1 Type Module General System InformationVAC Transformer Page 760 Direct Spark Ignition DSI Flowchart Lockout Until power is removed From controlTroubleshooting Test EquipmentDSI Ignitor GAP Feeler Gauge 1/8 Page Page First Visual Check Second Visual Check Third Visual Check For Leaks Withaflame Blink Green Continuously Continuously Page For 120 VAC application only ADC PN 128927 5N7 Redundant GAS Valve Direct Spark Ignition DSI System Components Phase 5 Coin System Diagnosis TroubleshootingDiagnostics L.E.D. Display Failure Codes Page D. Display Indicators No Heat Condition Blower is on Page No Start Condition No Display Condition 115 VACDSFL Display Condition DOOr Display Condition Data Label Information Data LabelUsing a Manometer HOW to USE a Manometer ADC PNLight Emitting Diode L.E.D. Display Codes Page Page ADC450213 1 08/18/03-25
Related manuals
Manual 38 pages 18.19 Kb

AD-360X2 specifications

The ADC AD-360X2 is a high-performance audio component designed for audiophiles and professionals who demand quality and reliability. This digital-to-analog converter (DAC) is engineered to deliver superior sound quality, with an emphasis on precision and clarity.

One of the standout features of the AD-360X2 is its dual DAC architecture, which utilizes two high-end digital-to-analog chips to ensure a pristine audio output. This design not only enhances the audio resolution but also minimizes noise and distortion, resulting in a richer listening experience. The device supports high-resolution formats, including DSD and PCM, enabling users to enjoy their music in the highest quality available.

The AD-360X2 also boasts a wide range of connectivity options, allowing it to interface seamlessly with various audio devices. It includes USB, optical, and coaxial inputs, making it compatible with computers, CD players, and digital media players. This versatility means that users can easily integrate the AD-360X2 into their existing audio setup, enhancing their overall experience.

Another impressive characteristic of the AD-360X2 is its built-in headphone amplifier. This feature allows users to connect their headphones directly to the unit, providing an optimized listening experience without the need for additional equipment. The headphone amplifier is designed to drive a wide range of headphone impedances, ensuring compatibility with everything from high-impedance studio headphones to more consumer-oriented options.

Additionally, the AD-360X2 integrates advanced clock technology to enhance timing accuracy. The precision clock circuit works to reduce jitter, which is often a major source of distortion in digital audio systems. By ensuring that the signal is processed with impeccable timing, the device further elevates audio quality.

User-friendliness is another significant aspect of the AD-360X2. The device features a straightforward control interface, with an easy-to-read display that provides real-time information about the audio being played. This simplicity ensures that both novices and seasoned audio enthusiasts can operate the device with ease.

In conclusion, the ADC AD-360X2 is an exemplary digital-to-analog converter that combines high-end audio performance with user-friendly features. Its dual DAC architecture, extensive connectivity options, built-in headphone amplifier, and advanced clock technology make it a standout choice for anyone seeking to elevate their audio experience. Whether for personal use or professional applications, the AD-360X2 is engineered to meet and exceed the expectations of discerning audio lovers.
Top Page Image Contents