ADC AD-360X2 manual To Replace Keyboard Touch PAD, To Replace Coin Acceptor

Page 20

5.Disconnect the keyboard (touch pad) connector from the computer board keyboard (touch pad) harness (simply pull straight out).

6.Disconnect the 9-pin main computer harness from the computer (squeeze the one [1] tab on the connector and pull straight back).

7.Disconnect the green ground wire from the computer board.

8.Remove the two (2) Phillips head screws that secure the computer to the panel. Remove the board from the panel by pulling at the corners of the board.

9.Replace in the reverse steps of the above.

10.Reestablish power to the dryer.

NOTE: Use caution when handling the microprocessor controller (computer) as it can be easily damaged by static electricity.

TO REPLACE KEYBOARD (TOUCH PAD)

1. Discontinue power to the dryer.

2. Open the coin panel and disconnect the keyboard (touch pad) ribbon connector from the ribbon cable it is plugged into.

3. Peel the keyboard (touch pad) from the front of the control panel taking care to avoid scratching the panel.

4.Clean any adhesive residue from the panel.

5.Peel off paper backing from new keyboard (touch pad).

6.Align the display window on the keyboard (touch pad) with the cutout in the control panel and press in place.

7.Connect keyboard (touch pad) ribbon to the board and reconnect power to the dryer.

8.Test for operation by pressing each temperature selection.

TO REPLACE COIN ACCEPTOR

1.Discontinue power to the dryer.

2.Open the coin panel.

3.Remove the four (4) 3mm nuts holding the coin acceptor to the panel.

4.Unplug optic switch harness connector.

5.Pull coin acceptor out gently.

6.Reverse procedure for installing new acceptor.

16

Page 19 Page 21
Image 20
Page 19 Page 21
Contents AD-360X2 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Data Label Information Safety Precautions Important InformationSuggested Interval Routine MaintenanceCleaning Adjustments AS RequiredInstallation Requirements ENCLOSURE, AIR SUPPLY, and Exhaust RequirementsElectrical and GAS Requirements Electrical RequirementsOperational Service Check Procedure Description of Parts Control PanelControl and Relay Panels Coin BOXDoor Switch Hinge Block Microprocessor AssemblyBasket Tumbler and Drive Motor Assembly Arrangement Basket TumblerDrive Motor and Idler Pulley Arrangement Idler ARM and Impellor Mount AssemblyTemperature Sensors HI-LIMIT Thermostat Sail SwitchGAS Burner Lint Drawer Lint Drawer SwitchFront Thruster Wheel Bracket Assembly Rotational Sensor Assembly Rear Basket Tumbler Drive WheelsService IntroductionControls Computer To Replace ComputerTo Replace Keyboard Touch PAD To Replace Coin AcceptorTo Replace GAS Valve To Replace the Ignitor Probe Burner Controls GAS To Test and Adjust GAS Water Column W.C. Pressure To Convert from Natural to Liquid Propane L.P. GAS To Replace HI-LIMIT Thermostat Thermostats and Temperature SensorTo Replace Direct Spark Ignition DSI Module To Remove the Temperature Sensor or High Heat Protector To Adjust Sail Switch Sail Switch AssemblyTo Replace Sail Switch To Replace Main Door Switch To Install NEW Main Door GlassFront Panel and Main Door Assemblies To Replace Main Door Hinge BlocksTo Replace Front Panel To Replace the Nylon CatchTo Replace Rotational Sensor Switch Basket Tumbler Removal Basket Tumbler Wheel RemovalBCD-1 Type Module General System InformationVAC Transformer Page 760 Direct Spark Ignition DSI Flowchart Lockout Until power is removed From controlTroubleshooting Test EquipmentDSI Ignitor GAP Feeler Gauge 1/8 Page Page First Visual Check Second Visual Check Third Visual Check For Leaks Withaflame Blink Green Continuously Continuously Page For 120 VAC application only ADC PN 128927 5N7 Redundant GAS Valve Direct Spark Ignition DSI System Components Diagnostics L.E.D. Display Failure Codes TroubleshootingPhase 5 Coin System Diagnosis Page D. Display Indicators No Heat Condition Blower is on Page No Start Condition No Display Condition 115 VACDSFL Display Condition DOOr Display Condition Data Label Information Data LabelUsing a Manometer HOW to USE a Manometer ADC PNLight Emitting Diode L.E.D. Display Codes Page Page ADC450213 1 08/18/03-25
Related manuals
Manual 38 pages 18.19 Kb

AD-360X2 specifications

The ADC AD-360X2 is a high-performance audio component designed for audiophiles and professionals who demand quality and reliability. This digital-to-analog converter (DAC) is engineered to deliver superior sound quality, with an emphasis on precision and clarity.

One of the standout features of the AD-360X2 is its dual DAC architecture, which utilizes two high-end digital-to-analog chips to ensure a pristine audio output. This design not only enhances the audio resolution but also minimizes noise and distortion, resulting in a richer listening experience. The device supports high-resolution formats, including DSD and PCM, enabling users to enjoy their music in the highest quality available.

The AD-360X2 also boasts a wide range of connectivity options, allowing it to interface seamlessly with various audio devices. It includes USB, optical, and coaxial inputs, making it compatible with computers, CD players, and digital media players. This versatility means that users can easily integrate the AD-360X2 into their existing audio setup, enhancing their overall experience.

Another impressive characteristic of the AD-360X2 is its built-in headphone amplifier. This feature allows users to connect their headphones directly to the unit, providing an optimized listening experience without the need for additional equipment. The headphone amplifier is designed to drive a wide range of headphone impedances, ensuring compatibility with everything from high-impedance studio headphones to more consumer-oriented options.

Additionally, the AD-360X2 integrates advanced clock technology to enhance timing accuracy. The precision clock circuit works to reduce jitter, which is often a major source of distortion in digital audio systems. By ensuring that the signal is processed with impeccable timing, the device further elevates audio quality.

User-friendliness is another significant aspect of the AD-360X2. The device features a straightforward control interface, with an easy-to-read display that provides real-time information about the audio being played. This simplicity ensures that both novices and seasoned audio enthusiasts can operate the device with ease.

In conclusion, the ADC AD-360X2 is an exemplary digital-to-analog converter that combines high-end audio performance with user-friendly features. Its dual DAC architecture, extensive connectivity options, built-in headphone amplifier, and advanced clock technology make it a standout choice for anyone seeking to elevate their audio experience. Whether for personal use or professional applications, the AD-360X2 is engineered to meet and exceed the expectations of discerning audio lovers.
Top Page Image Contents