ADC AD-360X2 manual DSI Ignitor GAP Feeler Gauge 1/8

Page 38

DSI IGNITOR GAP FEELER GAUGE (1/8”)

MULTIMETER/VOLTMETER

For checking the gap between ignitor assembly ground rod and spark electrode.

For measuring voltage and/or amperage

Available from ADC - Part No. 305410

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.Direct Spark Ignition (DSI) Troubleshooting Terms (Definitions)

a.LOCKOUT Mode - DSI module “GREEN” light emitting diode (L.E.D.) indicator light blinks continuously. This indicates there is a system fault and most likely the fault is that the DSI module was not able to ignite the gas.

b.FLAMEOUT - Burner flame shutdown by the DSI module due to lack of flame verification. This condition occurs only after ignition has been evident, but, is lost. The system will attempt to relight the burner after 30-seconds.

2.Troubleshooting/System Basic Diagnosis

a.Preliminary Steps - The following steps must be performed to minimize the time required to isolate cause of fault.

1)DSI module L.E.D. indicator is off (no “GREEN” light).

a)Check for voltage (approximately 24 VAC) across the DSI module terminals “THS” and “GND” (ground)...

If voltage (approximately 24 VAC) is evident, then, there is a malfunction within the DSI module itself, and it must be replaced.

b)If there is no voltage, and the problem is not the DSI module or the ignition system, then the problem is elsewhere in the dryer (i.e., dryers’ heat circuit [sail switch, hi-limit circuits, etc.]).

34

Page 37 Page 39
Image 38
Page 37 Page 39
Contents AD-360X2 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Data Label Information Safety Precautions Important InformationSuggested Interval Routine MaintenanceCleaning Adjustments AS RequiredInstallation Requirements ENCLOSURE, AIR SUPPLY, and Exhaust RequirementsElectrical and GAS Requirements Electrical RequirementsOperational Service Check Procedure Control and Relay Panels Description of PartsControl Panel Coin BOXBasket Tumbler and Drive Motor Assembly Arrangement Door Switch Hinge BlockMicroprocessor Assembly Basket TumblerDrive Motor and Idler Pulley Arrangement Idler ARM and Impellor Mount AssemblyTemperature Sensors HI-LIMIT Thermostat Sail SwitchGAS Burner Lint Drawer Lint Drawer SwitchFront Thruster Wheel Bracket Assembly Rotational Sensor Assembly Rear Basket Tumbler Drive WheelsControls Computer ServiceIntroduction To Replace ComputerTo Replace Keyboard Touch PAD To Replace Coin AcceptorTo Replace GAS Valve To Replace the Ignitor Probe Burner Controls GAS To Test and Adjust GAS Water Column W.C. Pressure To Convert from Natural to Liquid Propane L.P. GAS To Replace HI-LIMIT Thermostat Thermostats and Temperature SensorTo Replace Direct Spark Ignition DSI Module To Remove the Temperature Sensor or High Heat Protector To Adjust Sail Switch Sail Switch AssemblyTo Replace Sail Switch Front Panel and Main Door Assemblies To Replace Main Door SwitchTo Install NEW Main Door Glass To Replace Main Door Hinge BlocksTo Replace Front Panel To Replace the Nylon CatchTo Replace Rotational Sensor Switch Basket Tumbler Removal Basket Tumbler Wheel RemovalBCD-1 Type Module General System InformationVAC Transformer Page 760 Direct Spark Ignition DSI Flowchart Lockout Until power is removed From controlTroubleshooting Test EquipmentDSI Ignitor GAP Feeler Gauge 1/8 Page Page First Visual Check Second Visual Check Third Visual Check For Leaks Withaflame Blink Green Continuously Continuously Page For 120 VAC application only ADC PN 128927 5N7 Redundant GAS Valve Direct Spark Ignition DSI System Components Diagnostics L.E.D. Display Failure Codes TroubleshootingPhase 5 Coin System Diagnosis Page D. Display Indicators No Heat Condition Blower is on Page No Start Condition No Display Condition 115 VACDSFL Display Condition DOOr Display Condition Data Label Information Data LabelUsing a Manometer HOW to USE a Manometer ADC PNLight Emitting Diode L.E.D. Display Codes Page Page ADC450213 1 08/18/03-25
Related manuals
Manual 38 pages 18.19 Kb

AD-360X2 specifications

The ADC AD-360X2 is a high-performance audio component designed for audiophiles and professionals who demand quality and reliability. This digital-to-analog converter (DAC) is engineered to deliver superior sound quality, with an emphasis on precision and clarity.

One of the standout features of the AD-360X2 is its dual DAC architecture, which utilizes two high-end digital-to-analog chips to ensure a pristine audio output. This design not only enhances the audio resolution but also minimizes noise and distortion, resulting in a richer listening experience. The device supports high-resolution formats, including DSD and PCM, enabling users to enjoy their music in the highest quality available.

The AD-360X2 also boasts a wide range of connectivity options, allowing it to interface seamlessly with various audio devices. It includes USB, optical, and coaxial inputs, making it compatible with computers, CD players, and digital media players. This versatility means that users can easily integrate the AD-360X2 into their existing audio setup, enhancing their overall experience.

Another impressive characteristic of the AD-360X2 is its built-in headphone amplifier. This feature allows users to connect their headphones directly to the unit, providing an optimized listening experience without the need for additional equipment. The headphone amplifier is designed to drive a wide range of headphone impedances, ensuring compatibility with everything from high-impedance studio headphones to more consumer-oriented options.

Additionally, the AD-360X2 integrates advanced clock technology to enhance timing accuracy. The precision clock circuit works to reduce jitter, which is often a major source of distortion in digital audio systems. By ensuring that the signal is processed with impeccable timing, the device further elevates audio quality.

User-friendliness is another significant aspect of the AD-360X2. The device features a straightforward control interface, with an easy-to-read display that provides real-time information about the audio being played. This simplicity ensures that both novices and seasoned audio enthusiasts can operate the device with ease.

In conclusion, the ADC AD-360X2 is an exemplary digital-to-analog converter that combines high-end audio performance with user-friendly features. Its dual DAC architecture, extensive connectivity options, built-in headphone amplifier, and advanced clock technology make it a standout choice for anyone seeking to elevate their audio experience. Whether for personal use or professional applications, the AD-360X2 is engineered to meet and exceed the expectations of discerning audio lovers.
Top Page Image Contents