ADC AD-360X2 manual Front Panel and Main Door Assemblies, To Replace Main Door Switch

Page 29

F. FRONT PANEL AND MAIN DOOR ASSEMBLIES

TO REPLACE MAIN DOOR SWITCH

1. Discontinue power to the dryer.

2. Open main door.

3. Remove the two (2) Phillips head screws holding the main door switch in place.

4.Disassemble door switch bracket by removing the two (2) nuts holding the door switch to the housing, and remove the door switch.

5.Reverse this procedure for installing new door switch.

IMPORTANT: UNDER NO CIRCUMSTANCES should the door switch be disabled.

TO REPLACE MAIN DOOR HINGE BLOCKS

1.Discontinue power to the dryer.

2.Remove the two (2) top 3/16” Allen screws securing the top hinge pin to the front panel.

3.Remove the door from the dryer by lifting the door off the bottom hinge pin.

4.Remove the bottom hinge pin assembly from the front panel, two (2) 3/16” Allen screws securing the hinge pin to the front panel.

NOTE: Be careful not to lose the plastic washer on the hinge pin.

5. Reassemble by reversing steps.

TO INSTALL NEW MAIN DOOR GLASS

1.Remove main door assembly from the dryer (follow main door hinge removal procedure).

2.Place the main door on a flat surface with front of door face down.

3.Remove glass and clean ALL old sealant off main door. This area must be completely cleaned for correct bonding.

4.Apply a narrow bead of silicone (ADC PN: 170730) ALL around main door area where glass will rest.

5.Install glass on to door and adhesive and slightly press glass in place.

IMPORTANT: DO NOT press hard or silicone thickness between the glass and door will be reduced resulting in poor bonding.

6.The door assembly should now be put in an area where it will not be disturbed for at least 24-hours. Depending on the conditions, the curing time of the adhesive is 24- to 36-hours.

7.After 24-hour curing period, install main door on dryer by reversing Step #1.

25

Page 28 Page 30
Image 29
Page 28 Page 30
Contents AD-360X2 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Data Label Information Important Information Safety PrecautionsSuggested Interval Routine MaintenanceCleaning AS Required AdjustmentsENCLOSURE, AIR SUPPLY, and Exhaust Requirements Installation RequirementsElectrical Requirements Electrical and GAS RequirementsOperational Service Check Procedure Control Panel Description of PartsControl and Relay Panels Coin BOXMicroprocessor Assembly Door Switch Hinge BlockBasket Tumbler and Drive Motor Assembly Arrangement Basket TumblerDrive Motor and Idler Pulley Arrangement Idler ARM and Impellor Mount AssemblyTemperature Sensors HI-LIMIT Thermostat Sail SwitchGAS Burner Lint Drawer Lint Drawer SwitchFront Thruster Wheel Bracket Assembly Rear Basket Tumbler Drive Wheels Rotational Sensor AssemblyIntroduction ServiceControls Computer To Replace ComputerTo Replace Coin Acceptor To Replace Keyboard Touch PADTo Replace GAS Valve To Replace the Ignitor Probe Burner Controls GAS To Test and Adjust GAS Water Column W.C. Pressure To Convert from Natural to Liquid Propane L.P. GAS To Replace HI-LIMIT Thermostat Thermostats and Temperature SensorTo Replace Direct Spark Ignition DSI Module To Remove the Temperature Sensor or High Heat Protector To Adjust Sail Switch Sail Switch AssemblyTo Replace Sail Switch To Install NEW Main Door Glass To Replace Main Door SwitchFront Panel and Main Door Assemblies To Replace Main Door Hinge BlocksTo Replace the Nylon Catch To Replace Front PanelTo Replace Rotational Sensor Switch Basket Tumbler Wheel Removal Basket Tumbler RemovalGeneral System Information BCD-1 Type ModuleVAC Transformer Page Lockout Until power is removed From control 760 Direct Spark Ignition DSI FlowchartTest Equipment TroubleshootingDSI Ignitor GAP Feeler Gauge 1/8 Page Page First Visual Check Second Visual Check Third Visual Check For Leaks Withaflame Blink Green Continuously Continuously Page For 120 VAC application only ADC PN 128927 5N7 Redundant GAS Valve Direct Spark Ignition DSI System Components Diagnostics L.E.D. Display Failure Codes TroubleshootingPhase 5 Coin System Diagnosis Page D. Display Indicators No Heat Condition Blower is on Page No Start Condition 115 VAC No Display ConditionDSFL Display Condition DOOr Display Condition Data Label Data Label InformationHOW to USE a Manometer ADC PN Using a ManometerLight Emitting Diode L.E.D. Display Codes Page Page ADC450213 1 08/18/03-25
Related manuals
Manual 38 pages 18.19 Kb

AD-360X2 specifications

The ADC AD-360X2 is a high-performance audio component designed for audiophiles and professionals who demand quality and reliability. This digital-to-analog converter (DAC) is engineered to deliver superior sound quality, with an emphasis on precision and clarity.

One of the standout features of the AD-360X2 is its dual DAC architecture, which utilizes two high-end digital-to-analog chips to ensure a pristine audio output. This design not only enhances the audio resolution but also minimizes noise and distortion, resulting in a richer listening experience. The device supports high-resolution formats, including DSD and PCM, enabling users to enjoy their music in the highest quality available.

The AD-360X2 also boasts a wide range of connectivity options, allowing it to interface seamlessly with various audio devices. It includes USB, optical, and coaxial inputs, making it compatible with computers, CD players, and digital media players. This versatility means that users can easily integrate the AD-360X2 into their existing audio setup, enhancing their overall experience.

Another impressive characteristic of the AD-360X2 is its built-in headphone amplifier. This feature allows users to connect their headphones directly to the unit, providing an optimized listening experience without the need for additional equipment. The headphone amplifier is designed to drive a wide range of headphone impedances, ensuring compatibility with everything from high-impedance studio headphones to more consumer-oriented options.

Additionally, the AD-360X2 integrates advanced clock technology to enhance timing accuracy. The precision clock circuit works to reduce jitter, which is often a major source of distortion in digital audio systems. By ensuring that the signal is processed with impeccable timing, the device further elevates audio quality.

User-friendliness is another significant aspect of the AD-360X2. The device features a straightforward control interface, with an easy-to-read display that provides real-time information about the audio being played. This simplicity ensures that both novices and seasoned audio enthusiasts can operate the device with ease.

In conclusion, the ADC AD-360X2 is an exemplary digital-to-analog converter that combines high-end audio performance with user-friendly features. Its dual DAC architecture, extensive connectivity options, built-in headphone amplifier, and advanced clock technology make it a standout choice for anyone seeking to elevate their audio experience. Whether for personal use or professional applications, the AD-360X2 is engineered to meet and exceed the expectations of discerning audio lovers.
Top Page Image Contents