American Dryer Corp ADH-170 Preoperational Instructions, Non-Coin Models, Shutdown Instructions

Page 30

Microprocessor Models – Spin and dwell (stop) times are adjustable in the Manual (timed) Mode. Spin and dwell (stop) times are not adjustable in the Automatic Mode and have been preprogrammed into the microprocessor controller (computer) for 150-seconds spin time in forward direction, 120-seconds in the reverse direction and a 5-second dwell (stop) time.

Mechanical Timer Models – Timer models have an electronic reversing timer in the electrical service box, which is located in the upper right front area of the dryer.

Both the dwell (stop) time and the tumbler spin time are adjustable by mode selection switches located on the electronic timer (as noted in the illustration below).

TIMING LEGEND

SPIN TIME

Adjustment Position Number

1

2

3

4

5

 

 

 

 

 

 

Time in Seconds*

30

60

90

120

150

 

 

 

 

 

 

DWELL (STOP) TIME

 

 

 

 

 

 

 

 

 

 

 

Adjustment Position Number

1

2

3

4

5

 

 

 

 

 

 

Time in Seconds*

5

6.3

7.6

8.9

10.2

 

 

 

 

 

 

* Values shown are +/- 1-second.

Preoperational Instructions __________

Important

! For more detailed information regarding the microprocessor controller (computer), refer to the

microprocessor user’s manual included with the dryer.

Non-Coin Models

Microprocessor Controller (Computer)

The L.E.D. display reads “READY” (no cycle in progress).

Press the letter on the keypad corresponding to the cycle desired (i.e., key “D”).

The dryer will then start (i.e., blower, tumbler, and heat).

The L.E.D. display will read MANUAL DRYING CYCLE D, 00:00

MIN REMAIN.

Note

!The dryer can be stopped at any time by pressing the “STOP/CLEAR” key, at this time the dryer will

go into a cycle pause. If the “STOP/CLEAR” key is pressed again at this point, the cycle that was in progress will be cancelled and returned to the “READY” state.

When the programmed drying time has expired, the Phase 7 non-coin microprocessor controller (computer) will proceed into the Cool Down Cycle.

Once the Cool Down Cycle begins at the end of the heat cycle, the L.E.D. display will read COOL DOWN TEMP ___/

___ MINUTES remaining. At the end of the heat cycle, the dryer will shut off the heat and continue the fan and tumbler until the Cool Down Time or temperature is reached.

Mechanical Timer

Turn drying timer knob for a time of 20 minutes. Select “High Temp.”

Push “Push to Start” button.

To stop the dryer, open the main door.

Shutdown Instructions ________________

If the dryer is to be shutdown (taken out of service) for a period of time, the following must be performed:

Discontinue power to the dryer either at the external disconnect switch or the circuit breaker.

Discontinue the heat supply:

Steam Models – Discontinue the steam supply. SHUT OFF external (location furnished) shutoff valve.

SHUT OFF internal steam valves in the supply lines and the return lines.

30

American Dryer Corp.

113247 - 3

Image 30
Contents Installation Manual American Dryer CorporationRetain This Manual in a Safe Place for Future Reference Table of Contents Safety Precautions What To Do If You Smell GasADH-75 Specifications 54.61 cmADEH-75 Hepa Filter Dryer ADH-120 Specifications ADEH-120 Hepa Filter Dryer ADSH-120 Hepa Filter Dryer ADSH-120 Component Identification Front View ADSH-120 Component Identification Rear View ADH-170 Specifications 79.69 cmADSH-170 Hepa Filter Dryer ADSH-170 Component Identification Front View ADSH-170 Component Identification Rear View Location Requirements Installation ProceduresUnpacking/Setting Up Leveling Dryer ADH-75Dryer Enclosure Requirements Fresh Air Supply RequirementsExhaust Requirements Outside Ductwork ProtectionSingle Dryer Venting Horizontal Venting Vertical VentingADH-120 Multiple Dryer Common VentingADH-75 ADH-170Electrical Information ADEH-170 Electric Models Only ADEH-75 Electric Models OnlyADEH-120 Electric Models Only GroundingSteam Models Only Single-Phase 1ø ADSH-75 Only Wiring Connections/HookupElectrical Connections For 110V ApplicationsPhase 3ø Wiring Connections/Hookup For 208-240V ApplicationsElectrically Heated Models Only Steam Information Steam Coil pH LevelSteam Requirements High Pressure Steam Damper Air System Connections Installation InstructionsSteam Damper System Operation Adjustment ADSH-120 Only Air RequirementsSteam Damper System Operation Filter Information Hepa Pressure Gauge/Alarm AddendumFilter Replacement ADH-75, ADH-170Preparation for Operation/Start-Up Preoperational TestNon-Coin Models Mechanical TimerPreoperational Instructions Shutdown InstructionsService/Parts Information Warranty InformationRoutine Maintenance Procedure for Functional Check Replacement Components Data Label InformationManual Reset Burner Hi-Limit Instructions High Temperature AlarmDoor Interlock 113247 ADC Part No 08/15/07

ADH-120, ADH-75, ADH-170 specifications

American Dryer Corp is renowned for its high-quality commercial dryer machines, catering to the needs of various industries, particularly in laundromats, hospitality, and healthcare. Among their extensive lineup, the ADH-170, ADH-75, and ADH-120 stand out for their efficiency, durability, and innovative technology designed to enhance user experience and operational efficiency.

The ADH-170 is a heavy-duty dryer known for its impressive capacity and rapid drying times. With a substantial drum size, it can accommodate large loads, making it ideal for high-traffic commercial environments. This model features advanced moisture sensing technology that automatically adjusts drying times based on the moisture content of the load, ensuring optimal performance while conserving energy. The durable construction and rust-resistant materials also mean that the ADH-170 is built to withstand the rigors of daily use.

The ADH-75 is designed for establishments that require a balance of capacity and efficiency. It offers a slightly smaller drum size compared to the ADH-170 but maintains robust performance characteristics. This model is equipped with an intuitive control panel that allows operators to select various drying cycles and settings, optimizing the dryer’s performance for different fabric types. The ADH-75 also incorporates energy-saving features, such as a cool-down cycle that helps prevent fabric from overheating, thus prolonging garment life.

The ADH-120 is a versatile dryer that strikes an excellent balance between capacity and flexibility. This model comes with an innovative air-flow design, promoting quicker drying times and reducing energy consumption. Its ergonomic design ensures ease of use, while safety features protect operators and users alike. Furthermore, the ADH-120 is outfitted with user-friendly controls that provide programmable settings, making it suitable for various commercial applications.

Overall, the American Dryer Corp ADH series exemplifies a commitment to quality and performance in commercial laundry solutions. From the high-capacity ADH-170 to the efficient ADH-75 and the adaptable ADH-120, each model integrates advanced technology and robust design, making them reliable choices for businesses looking to optimize their laundry operations. With their user-friendly features and energy-efficient solutions, American Dryer Corp continues to set the standard in the commercial dryer market, ensuring customer satisfaction and operational excellence.