Amana W10150613B Under the outer terminal block screws hooks facing right, Venting Requirements

Page 9

3.Connect ground wire (green or bare) of power supply cable to external ground conductor screw. Tighten screw.

A B

C

1.Loosen or remove center silver-colored terminal block screw.

2.Connect neutral wire (white or center wire) of power supply cord to the center, silver-colored terminal screw of the terminal block. Tighten screw.

B C

F E

D

A. External ground conductor screw

B. Center silver-colored terminal block screw

A

D

E

 

C. Neutral wire (white or center wire)

 

D. ¾" (19 mm) UL listed strain relief

 

E. Ground wire (green or bare) of power supply cable

 

F. Neutral ground wire

4.

Place the hooked ends of the other power supply cable wires

 

under the outer terminal block screws (hooks facing right).

 

Squeeze hooked ends together. Tighten screws.

5.

Tighten strain relief screws.

6.

Insert tab of terminal block cover into slot of dryer rear panel.

 

Secure cover with hold-down screw.

7.

You have completed your electrical connections. Now go to

 

“Venting Requirements.”

3-wire connection: Power Supply Cord

Use where local codes permit connecting cabinet-ground conductor to neutral wire:

B D E

A

CG F

A.3-wire receptacle (NEMA type 10-30R)

B.3-wire plug

C.Neutral prong

D.Spade terminals with up turned ends

E.¾" (19 mm) UL listed strain relief

F. Ring terminals

G. Neutral (white or center wire)

A. Neutral ground wire

B. External ground conductor screw

C. Center silver-colored terminal block screw

D. Neutral wire (white or center wire)

E. ¾" (19 mm) UL listed strain relief

3.Connect the other wires to outer terminal block screws. Tighten screws.

4.Tighten strain relief screws.

5.Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

6.You have completed your electrical connections. Now go to “Venting Requirements.”

3-wire connection: Direct Wire

Use where local codes permit connecting cabinet-ground conductor to neutral wire.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can be moved if needed.

Strip 312" (89 mm) of outer covering from end of cable. Strip insulation back 1" (25 mm). If using 3-wire cable with ground wire, cut bare wire even with outer covering. Bend ends of wires into a hook shape.

1" (25mm)

3

 

"

2

1

 

(89

mm)

 

 

When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw, as shown.

9

Image 9
Contents 29 73.7 CM Electric Dryer Installation Instructions Location Requirements Tools and PartsParts supplied Parts neededMobile Home Additional Installation Requirements Installation ClearancesElectrical Requirements U.S.A It is your responsibilityIf connecting by direct wire Electrical ConnectionIf your outlet looks like this Canada Electrical Requirements CanadaInstall strain relief Power Supply Cord Direct WireStyle 1 Power supply cord strain relief Electrical Connection U.S.A. OnlyStyle 2 Direct wire strain relief Wire connection Power Supply CordRemove center silver-colored terminal block screw Wire connection Direct WireSqueeze hooked ends together. Tighten screws Under the outer terminal block screws hooks facing rightSecure cover with hold-down screw You have completed your electrical connections. Now go toOptional 3-wire connection If using an existing vent system Venting RequirementsIf this is a new vent system Vent material Special provisions for mobile home installations Plan Vent SystemDetermine vent path Install Leveling Legs Install Vent SystemVent system chart Level DryerReverse Door Swing Optional Reversible Large Side-Swing DoorReversible Super Wide Side-Swing Door U.S.A Complete InstallationCanada If the dryer will not start, check the followingSécurité DE LA Sécheuse Outillage et pièces Exigences d’emplacementSpécifications électriques Canada ’installation dans une maison mobile exige’est à l’utilisateur qu’incombe la responsabilité de Espacement requisEn cas dutilisation du système dévacuation existant Exigences concernant l’évacuationLe clapet incliné de type boîte ci-dessous est acceptable Planification du système d’évacuationInstallation des pieds de nivellement Installation du système d’évacuationDéterminer litinéraire dacheminement du conduit Une réduction de la longévité de la sécheuseRaccordement du conduit d’évacuation Mise à niveau de la sécheuseInversion du sens d’ouverture de la porte Facultatif Grande porte réversible à pivotement latéralSi la sécheuse ne démarre pas, vérifier ce qui suit Achever l’installationTous droits réservés W10150612B SP PN W10150613B