American Dryer Corp MLG-460 manual Verify Pendant Electrical Signals

Page 92

TUMBLER (Basket) FORWARD “PENDANT” - PB1

This push button comprises of one normally open switch, and is mechanically interlocked with the Tumbler (Basket) Reverse Push button.

EMERGENCY STOP ((E-Stop) “PENDANT” - PB6

This push button switch is normally open device and its function is to shut down the control voltage to the dryer in the event it is pressed.

NOTE: It will not effect the sprinkler circuit power.

2.Verify Pendant Electrical Signals

ALL the pendant control signals are interfaced to the Main Electrical Panel’s PLC (Programmable Logic Controller) except for EMERGENCY STOP (E-Stop).

Load - Level - Unload -A and B

Tumbler (Basket) Reverse Switch - PB2

Tumbler (Basket) Forward Switch -PB1

EMERGENCY STOP (E-Stop) Switch - PB6

For a quick check of the wiring of SEL 1 and 2 to the PLC (Programmable Logic Controller) perform the following test with the control voltage “ON” (“GREEN” Button);

Turn the selector switch to “LOAD.”

Does PLC (Programmable Logic Controller) input L.E.D. (light emitting diode) #15 light?

Turn the selector switch to “UNLOAD.”

Does PLC (Programmable Logic Controller) input L.E.D. (light emitting diode) #16 light?

Turn the selector switch to “LEVEL.”

Are both PLC (Programmable Logic Controller) (input #15 and input #16) “OFF”?

If the answers to these question are “YES,” wiring to the PLC (Programmable Logic Controller) is correct.

If any answer to these questions is “NO”, refer to Probable Causes paragraph on page 89.

Tumbler (Basket) Reverse Switch PB2

For a quick check of the wiring of PB2 to the PLC (Programmable Logic Controller) perform the following test with control voltage “ON”. (“GREEN” Button)

Press the REVERSE push-button.

Does PLC (Programmable Logic Controller) input L.E.D. (light emitting diode) #18 light?

88

Image 92
Contents MLG-460 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Troubleshooting TOC Service PartsReturning Warranty Cards Parts Returning Warranty Parts Section Safety Precautions What to do if YOU Smell GASPage Specifications SpecificationsSpecifications Installation Procedures Reassembly of DryerPage Page Location Requirements Internal AIR, Electric and Water Connections Page Page Page Page Page Left Drum Motor External Supply Connections Page Page Electrical Requirements Electrical RequirementsMLG-460 Page Fresh AIR Supply Requirements PRE START-UP Preparation for OperationRoutine Maintenance CleaningMonthly Component System Descriptions Page Page Main AIR Blower and Heat Reclaimer System Page Compressed AIR System Page Page GAS Burner and Ignition System Switch #2 Intermittent Pilot Page Page Page Page Page Page Page Safety Devices Door Open Service PartsReturning Warranty Parts Returning Warranty CardsWarranty Page Troubleshooting Probable Causes Power MalfunctionsPossible Solutions No Control Power Blue Light Off Machine Main Power Shuts Down Blue Indicator Off 2CRB Sprinkler Circuit Description Page Front Panel Blue Light and RED Light on Possible Solutions General Description Unless the Water Valve to the Sprinkler is ClosedBurner Controller Input Signal Components Burner IgnitionIntroduction Burner Section Input Circuit Component DescriptionLoad Door Switch DS1B Output Signal Component Description Stop Detector Relay Contact SMD noGAS Fault Message gas system only Heater Fault Message Possible Solutions Page Page AIR Fault Message HI-TEMP Fault Message Possible Solutions Drum Fault Message Page Tumbler Basket Section Electrical Malfunctions Tumbler Basket Section Electrical ComponentsFollowing is for 2-Door Models only Rear Panel Control Problems Probable Causes Possible Solutions Unload 1 Selection Probable Causes PLC OUT PIN 7 = Unload Door Open PLC OUT PIN 10 = Front UPDoor Open Problem Drum Fault Message Malfunction Probable Causes Page Front Door Switch Rear Down Switch LS2Lint Drawer Proximity Switches Base Section Electrical MalfunctionsProbable Solutions Lint Chamber Pressure Switch PS3Tumbler Basket Tilt Problems Level Fault Page Lint Screen Mechanism Problem Screen Fault Lint Chamber Air Pressure Problem AIR Fault Pendant Control Malfunctions Pendant Electrical ComponentsVerify Pendant Electrical Signals ML-460 Pendant Assembly Diagram Temperature Sensing Page Temperature Measurement and Sensing Problems Circuit Wiring to the Analog Input Module MotorsMotor Actuation Problems Probable Causes Motor Protection Device DescriptionsScreen Fault Motor FaultGAS Fault AIR Fault