Daewoo DWF-805 Trouble Shooting Guide, Concerning Water Supply, Water is Not SUP Plied, Yes

Page 26

8. TROUBLE SHOOTING GUIDE

NOTES

1. When replace the P.C.B. ASS’Y do not scratch the surface of the P.C.B. ASS’Y.

2. Disconnect the power cord from the electric outlet.

CONCERNING WATER SUPPLY

PROBLEM

WATER IS

NOT SUP-

PLIED.

CHECK POINT

Do you open the water

tap?

YES

Is the filter of the water inlet valve clogged with dirt?

NO

Is the water pressure sufficient?

(0.3~8 kgf/cm2)

YES

 

CAUSE

 

 

SOLUTION

 

 

 

 

 

 

NO

 

 

 

 

 

 

Open the water tap.

 

 

 

 

 

YES

 

 

 

 

 

 

 

 

 

 

Clean the filter.

 

 

 

 

 

 

 

 

 

 

NO

 

 

 

Increase the water pres-

 

 

 

 

 

sure.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE : Open the water tap fully and measure

 

 

 

the flow rate.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Flow

11.5

15.0

18.0

20.3

24.1

27.4

 

rate(l/min.)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Water pressure

0.3

0.4

0.5

0.6

0.8

1.0

 

(kgf/cm2)

 

 

 

 

 

 

 

 

 

From the upper results, you know that the flow rate more than 11.5l/min. is essential for water supply.

Does the water inlet valve make operating sound?

YES

Is the connector or the terminal connected properly?

YES

NO

NO

Water inlet valve is defective.

Improper connection of the connector or the ter- minal.

Change water inlet valve.

Connect the connector or the terminal properly.

Is the output voltage of the P.C.B normal?

YES

NO

P.C.B AS is defective.

Change the P.C.B AS.

 

Lead wire is defective.

 

 

Change the lead wires.

 

 

 

 

 

 

TROUBLE SHOOTING 25

Image 26
Contents Auto Washer Washing Machine Specifications DWF-802/805/808Structure of the Washing Machine Fuzzy → FUZZY+SOAK → Heavy → HEAVY+SOAK → Speedy → Suitwool Functions of the Control PanelCold → COLD+HOT → HOT Fuzzy → Heavy → Suitwool → Blanket → Speedy Directions for Installation and USE § Location of WasherFor Ordinary TAP For SCREW-SHAPED TAPCleaning the Drain Filter Cleaning the Lint FilterCleaning the Water Inlet Filter Water Flow Feature and Technical ExplanationEffect Automatic Drainning Time Adjustment Functional PrincipleFlow of the Softener HOW to Check MovementSoftener Dispenser Flow of the Softener Inside of the BalancerCIRCULATING-WATER Automatic Unbalance AdjustmentCIRCULATING-WATER Residual Time Display HOW to Replace Lint FilterLint Filter Drain MotorGear Mechanism ASS’Y Principle of Bubble GeneratorFunctional Principle of Bubble Washing Machine Principle of Intake & Outlet of the AIRFunctional Principle of Trans & Magnet Across SectionDirections for Disassembly and Adjustment Gear Mechanism ASS’Y Replacement¡ Lay the front of the washer on the floor Motor Synchronous and Valve Replacementnon Pump Model Brake AdjustmentStructure of Gear Mechanism ¡ Tool for Replacing the Clutch Boss ASSEMBLE¡Problem HOW to Check the Clutch Spring ProblemProcess Process of DisassembleProcess Process of Assemble Use fixing jig and 17mm Water is Not SUP Plied Trouble Shooting GuideConcerning Water Supply YESPUL Sator does Not Rotate Even if Water is Suppled Water SUP PLY is not StoppedConcerning Washing Concerning Draining Washer Does not DrainConcerning Spinning Washer Does not Spin YESDo not Light UP Motor Rotates When START/HOLD Button is not PressedConcerning Operation Abnormal Noise DUR- ING Wash ProcessPresentation of the P.C.B ASS’Y Concerning Error MessageMessage Cause Solution Appendix § NON-PUMP,SINGLE Valve § Pump § PUMP, Single Valve Parts Diagram Part Name Part Code Specification Remark 5A COLD/HOT Bubble Dual Valve Cord Power AS5A COLD/HOT NON-BUBBLE Dual VALVE, Pump 5A COLD/HOT NON-BUBBLEParts Diagram Cabinet LEG Adjust ASWire Power Cord Painted Steel Sheet 0.6TParts Diagram TUB U Balancer ASTUB Stainless SteelParts Diagram Suspension AS F Cover TUB OTUB O Suspension AS BCircuit Diagram DWF-756/758/806/808 NO. WF750SE001