Maytag W10443046B-SP, W10443045B installation instructions Make GAS Connection, Connect Inlet Hoses

Page 13

2. Screw in leveling legs

2. Plan pipe fitting connection

diamond marking

A

B

A. 3/8" flexible gas connector B. 3/8" dryer pipe

D

C

C. 3/8" to 3/8" pipe elbow

D. 3/8" pipe-to-flare adapter fitting

Examine leveling legs, find diamond marking. Screw legs into leg holes by hand, use a wrench to finish turning legs until diamond marking is no longer visible.

Now stand the dryer on its feet. Slide the dryer until it is close to its final location. Leave enough room for electrical connection and to connect the exhaust vent.

MAKE GAS CONNECTION

1. Connect gas supply to dryer

Flared

Non-flared

B

male fitting

male fitting

 

Remove red cap from gas pipe. Using a wrench to tighten, connect gas supply to dryer. Use pipe-joint compound on threads of all non-flared male fittings. If flexible metal tubing is used, be sure there are no kinks.

NOTE: For LP gas connections, you must use pipe-joint compound resistant to action of LP gas. Do not use TEFLON®† tape.

†®TEFLON is a registered trademark of E.I. Dupont De Nemours and Company.

A combination of pipe fittings must be used to connect dryer to existing gas line. A recommended connection is shown. Your connection may be different, according to supply line type, size, and location.

3. Open shut-off valve

Closed valveA

BOpen valve

Open shut-off valve in supply line; valve is open when handle is parallel to gas pipe. Then, test all connections by brushing on an approved noncorrosive leak-detection solution.

Bubbles will show a leak. Correct any leaks found.

CONNECT INLET HOSES

For non-steam models, skip to “Connect Vent” on page 15.

The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses.

1. Turn cold water off, remove and replace rubber washer

Turn cold water faucet off and remove washer inlet hose.

Check and see if rubber washer is in the “Y” connector. Remove old rubber washer from inlet hose and replace with new rubber washer provided.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Table of Contents Table des matières Dryer Safety Page Tools needed for all installations Installation RequirementsParts supplied all models Parts supplied steam modelsLocation Requirements Dryer DimensionsYou will need Cabinet installation dryer only Closet installation dryer onlySpacing for recessed area or closet installation Electrical Requirements Electric Dryer Power Hookup Canada onlyGAS Supply Requirements GAS Dryer Power HookupGAS Type LP Gas ConversionGAS Supply Line Gas supply pressure testingGAS Supply Connection Requirements Burner Input RequirementsVenting Alternate installations for close clearances Recommended exhaust installationsOptional exhaust installations Plan Vent SystemInstall Leveling Legs Install Vent SystemInstall exhaust hood Connect vent to exhaust hoodConnect Inlet Hoses Make GAS ConnectionAttach long hose to Y connector and tighten couplings Attach short hose and Y connectorAttach long hose to dryer fill valve and tighten coupling Level Dryer Connect VentTroubleshooting Complete Installation ChecklistAdjust leveling legs Door ReversalSécurité DE LA Sécheuse QUE Faire Dans LE CAS D’UNE Odeur DE GAZ Pièces fournies tous les modèles Exigences D’INSTALLATIONPièces fournies modèles à vapeur Dimensions DE LA Sécheuse Exigences D’EMPLACEMENTIl vous faudra Vue porte ouverteInstallation dans un encastrement sécheuse Installation dans un placard sécheuseSeulement Spécifications Électriques Installation sous comptoir personnalisée sécheuse seulement’est à l’utilisateur qu’incombe la responsabilité de Toutes les sécheusesInstructions DE Liaison À LA Terre Raccordement D’UNE Sécheuse À GAZConservez CES Instructions Type DE GAZExigences Concernant LE Raccordement AU GAZ Canalisation DE GAZCaractéristiques D’ALIMENTATION DU Brûleur Canalisation D’ARRIVÉE DE GAZ DE LA SécheuseExigences Concernant L’ÉVACUATION ’ÉVACUATIONAutres installations où le dégagement est réduit Installations d’évacuations recommandéePlanification DU Système D’ÉVACUATION Brides de serrageTableau des systèmes d’évacuation standard Installations d’evacuation facultativesTableau des systèmes d’évacuation longues Dispositions spéciales pour les maisons mobilesInstallation DES Pieds DE Nivellement Installation DU Circuit D’ÉVACUATIONRaccordement DU Tuyau D’ARRIVÉE D’EAU Raccordement AU GAZRaccorder l’alimentation en gaz à la sécheuse Fermer l’eau froide retirer etSerrer les raccords Fixer le tuyau court et le raccord en YFixer le long tuyau au raccord en Y et serrer les raccords Réglage DE L’APLOMB DE LA Sécheuse Raccordement DU Conduit D’ÉVACUATIONInversion DE LA Porte Achever L’INSTALLATION Liste DE VérificationLaveuse ET Sécheuse Superposées Dépannage

W10443046B-SP, W10443045B specifications

The Maytag W10443045B and W10443046B-SP are exceptional solutions designed for those seeking reliability and performance in their kitchen appliances. These products are part of Maytag's reputation for durability and efficiency, making them ideal for daily use in busy households.

One of the main features of these models is their robust construction. Built with high-quality materials, they promise longevity and resilience against daily wear and tear. Both models are designed to offer easy installation, ensuring that users can set them up without requiring professional assistance. This user-friendly approach extends to their maintenance, as they are designed for easy cleaning and upkeep.

In addition to durability, the W10443045B and W10443046B-SP include advanced technological features. They come equipped with the latest in smart appliance technology, allowing users to monitor and control their settings through a dedicated mobile app. This capability offers convenience, ensuring that users can manage their appliances from virtually anywhere in their home.

Energy efficiency is another hallmark of these models. Maytag has integrated energy-saving technology into these products, helping users reduce their utility bills while also being environmentally conscious. The energy-efficient design maintains high performance without sacrificing power, embracing sustainability without compromising on functionality.

The design of both models is aesthetically pleasing, featuring sleek lines and a modern finish that complements a variety of kitchen styles. Their user-friendly controls make them accessible to everyone, while the spacious interior provides ample room for cooking and storing food items.

Safety features are also prioritized in the W10443045B and W10443046B-SP. These models include automatic shut-off systems and temperature controls that ensure safe operation during use. This focus on safety provides peace of mind for users who want to ensure their kitchen is a safe environment for family members.

Overall, the Maytag W10443045B and W10443046B-SP combine functionality, longevity, and modern technology, making them standout choices for consumers looking to upgrade their kitchen appliances. With their impressive features and thoughtful design, these models are sure to meet the needs of any contemporary household.
Top Page Image Contents