Humminbird MATRIX 12, MATRIX 37 manual Depth Alarm, Fish ID Alarm, Low Battery Alarm, Alarm Tone

Page 22

www..reelschel AlarmsmMenuaticT b ..com

From any view, press the MENU key twice to access the Main Menu System. The Alarms tab will be the default selection.

NOTE: When an alarm is triggered, you can silence it by pressing any key. The alarm will be silenced, and will not be triggered again until a new instance of the alarm condition is detected.

Alarms Menu

Depth Alarm

Depth Alarm sounds when the depth becomes equal to or less than the menu setting.

To change the Depth Alarm setting:

1.Highlight Depth Alarm on the Alarms main menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Depth Alarm setting. (OFF, 1 to 100 feet, or 0.5 to 30 meters [International Models Only], Default = OFF)

Fish ID Alarm

Fish ID Alarm sounds when the Fishing System detects fish that correspond to the alarm setting. Fish ID Alarm will only sound if Fish ID+TM is on.

For example, if you've set the Fish ID Alarm to sound for Large fish only, the Fish ID alarm will sound when a large-sized fish is detected.

To change the Fish ID Alarm setting:

1.Highlight Fish ID Alarm on the Alarms main menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Fish ID Alarm setting. (Off, All, Large/Medium, Large, Default = Off)

All

Large/Medium

Large

Low Battery Alarm

Low Battery Alarm sounds when the input battery voltage is equal to or less than the menu setting. The battery alarm will only sound for the battery that is connected to the Matrix Fishing System. The Low Battery Alarm should be set to warn you when the battery voltage drops below the safety margin that you have determined. For instance, if you are running a trolling motor (battery operated), you would want to set the Low Battery Alarm to sound before the battery voltage drops too low for it to be used to start your main, gasoline-powered engine.

To change the Low Battery Alarm setting:

1.Highlight Low Battery Alarm on the Alarms main menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Low Battery Alarm setting. (Off, 8.5V - 13.5V, Default = Off)

Alarm Tone

Alarm Tone selects the pitch of the alarm sound. A brief tone will be produced as you adjust the Alarm Tone so that you can select the tone that you can hear best.

To change the Alarm Tone setting:

1.Highlight Alarm Tone on the Alarms main menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Alarm Tone setting. (High, Medium, Low, Default = Medium)

37

38

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Operations Manual Table of Contents WwwThank You!..reelschel matic..comAccessories Menu Tab Troubleshooting Alarms Menu TabSetup Menu Tab Sonar Menu TabDualBeam Plus Sonar Single Beam SonarQuadraBeam Sonar Hard Bottom WwwWhat’s On..reelschelthe Disp ay matic..comBait Ball Soft BottomUnderstanding Sonar History Sonar ViewSonar View Full range view Sonar Zoom ViewSonar Zoom View 200/83 kHz Split Sonar View Big Digits ViewDualBeam Plus and QuadraBeamTM Only Big Digits ViewDigital readouts in the Side Beam View cannot be customized Bottom PresentationQuadraBeamTM Only Side Beam ViewKey Functions POWER/LIGHT KeyView Key WAY Cursor Control Key Exit KeyPowering Up the Unit AccessorymBusaticMenu System Start-Up Options Menu Normal OperationPC Connect System StatusWith PC Connect Cable Only Sensitivity To adjust the SensitivityTo adjust the Upper Range Upper RangeTo adjust the Chart Speed Chart SpeedTo adjust the Lower Range To adjust the Bottom ViewSonar Zoom View Only To adjust the Zoom LevelSonar Menu Tab Highlight Zoom Level on the Sonar X-PressTMMenuHighlight Beam Select on the Sonar main menu Fish ID+TMTo use Beam Select To turn Fish ID+ on or offKHz Sensitivity Real Time Sonar RTS WindowKHz Balance Surface Clutter To change the Depth Lines settingTo change the Surface Clutter setting AdvancedWater Type Max DepthTransducer Select Low Battery Alarm Depth AlarmFish ID Alarm Alarm ToneUnits Temp Units DepthUnits Distance Restore Defaults User ModeTriplog Reset LanguageTo Select Views TemperatureSelect Readouts Advanced, Sonar View OnlyDepth Offset To change the Depth Offset settingTo change the Temp Offset setting Temp OffsetNmea Output Accessories Menu TabTo change the Speed Calibration setting Advanced, with Temp/Speed OnlyProblem Possible Cause Display ProblemsControl head loses power at high speeds Matrix Fishing System Accessories IsolationSpecifications Contact Humminbird
Related manuals
Manual 31 pages 15.56 Kb
Top Page Image Contents