Humminbird Matrix 27, MATRIX 37, Matrix 20 User Mode, Language, Triplog Reset, Restore Defaults

Page 24

www..reelschelUnits - Sp md atic..com

(with Temp/Speed or GPS Receiver)

Units - Speed selects the units of measure for speed-related readouts, and will appear in the menu if a Temp/Speed Accessory is connected and the paddlewheel has moved at least once, or if a GPS Receiver is connected.

To change the Units - Speed setting:

1.Highlight Units - Speed on the Setup menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Units - Speed setting. (kph [International Models Only], mph, kts, Default = kph for International models and mph for Domestic models)

User Mode

User Mode sets the menu system to either Normal or Advanced. When set to Normal (default setting,) only the basic menu options are shown. When set to Advanced, additional menu choices are available.

To change the User Mode setting:

1.Highlight User Mode on the Setup menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the User Mode setting. (Normal, Advanced, Default = Normal)

Language

(International Only)

Language selects the display language for menus. International Models Only.

To change the Language setting:

1.Highlight Language on the Setup menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Language setting. (Default = English)

Triplog Reset

(with Temp/Speed or GPS Receiver)

Triplog Reset resets the Triplog to zero, and will appear in the menu if a Temp/Speed Accessory is connected and the paddlewheel has moved at least once, or if a GPS Receiver is connected. The Triplog provides the following information: timer for elapsed time, distance traveled since last reset, and average speed.

NOTE: See Setup Menu Tab: Select Readouts (Advanced) to find out how to display Triplog information on the screen.

To Reset Triplog:

1.Highlight Reset Triplog on the Setup menu.

2.Use the RIGHT 4-WAY Cursor Control key to initiate Triplog Reset.

3.The Confirm dialog box will appear. To reset the Triplog, press the RIGHT Cursor key once more. To cancel Reset Triplog, press the LEFT Cursor key.

Restore Defaults

Restore Defaults resets ALL menu settings to their factory defaults. Use this menu choice with caution!

To Restore Defaults:

1.Highlight Restore Defaults on the Setup menu.

2.Use the RIGHT 4-WAY Cursor Control key to initiate restoring defaults.

3.The Confirm dialog box will appear. To reset the defaults, press the RIGHT Cursor key once more. To cancel Restore Defaults, press the LEFT Cursor key.

41

42

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Operations Manual Table of Contents WwwThank You!..reelschel matic..comAlarms Menu Tab Setup Menu TabAccessories Menu Tab Troubleshooting Sonar Menu TabSingle Beam Sonar DualBeam Plus SonarQuadraBeam Sonar WwwWhat’s On..reelschelthe Disp ay matic..com Bait BallHard Bottom Soft BottomSonar View Understanding Sonar HistorySonar View Sonar Zoom View Full range viewSonar Zoom View Big Digits View DualBeam Plus and QuadraBeamTM Only200/83 kHz Split Sonar View Big Digits ViewBottom Presentation QuadraBeamTM OnlyDigital readouts in the Side Beam View cannot be customized Side Beam ViewPOWER/LIGHT Key Key FunctionsView Key WAY Cursor Control Key Exit KeyAccessorymBusatic Powering Up the UnitMenu System Start-Up Options Menu Normal OperationSystem Status PC ConnectWith PC Connect Cable Only To adjust the Sensitivity To adjust the Upper RangeSensitivity Upper RangeChart Speed To adjust the Lower RangeTo adjust the Chart Speed To adjust the Bottom ViewTo adjust the Zoom Level Sonar Menu TabSonar Zoom View Only Highlight Zoom Level on the Sonar X-PressTMMenuFish ID+TM To use Beam SelectHighlight Beam Select on the Sonar main menu To turn Fish ID+ on or offReal Time Sonar RTS Window KHz SensitivityKHz Balance To change the Depth Lines setting To change the Surface Clutter settingSurface Clutter AdvancedMax Depth Water TypeTransducer Select Depth Alarm Fish ID AlarmLow Battery Alarm Alarm ToneUnits Depth Units TempUnits Distance User Mode Triplog ResetRestore Defaults LanguageTemperature Select ReadoutsTo Select Views Advanced, Sonar View OnlyTo change the Depth Offset setting To change the Temp Offset settingDepth Offset Temp OffsetAccessories Menu Tab To change the Speed Calibration settingNmea Output Advanced, with Temp/Speed OnlyDisplay Problems Problem Possible CauseControl head loses power at high speeds Matrix Fishing System Accessories IsolationSpecifications Contact Humminbird
Related manuals
Manual 31 pages 15.56 Kb
Top Page Image Contents