Humminbird Matrix 20, MATRIX 37, MATRIX 12, MATRIX 17 Depth Offset, Temp Offset, To Select Readouts

Page 26

www..reelschel matic..com

Default Sonar View

Customized Sonar View

To Select Readouts:

1.Make sure you are in Advanced User Mode, then highlight Select Readouts on the Setup main menu.

2.Use the RIGHT 4-WAY Cursor Control key to initiate this procedure.

3.The Select Readouts submenu will appear, showing a list of all Readouts. Use the UP or DOWN Cursor keys to select a particular Readout position, then use the RIGHT or LEFT Cursor keys to change what will be displayed at that position. (Off, Speed, Temperature, Triplog, Voltage, Water Speed)

Depth Offset

(Advanced)

Depth Offset will adjust the digital depth readout to indicate depth from the waterline or boat's keel. Enter a positive vertical measurement from the transducer to the waterline to read the depth from the waterline. Enter a negative vertical measurement from the transducer to keel to read the depth from the keel. This menu choice is available only when in Advanced User Mode (see Setup Menu Tab: User Mode.)

To change the Depth Offset setting:

1.Make sure you are in Advanced User Mode, then highlight Depth Offset on the Setup menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Depth Offset setting. (-10.0 to +10.0 feet or -3 to 3 meters [International Models Only], Default = 0)

Temp Offset

(Advanced)

Temp Offset will adjust the temperature readout by the amount entered. This menu choice is available only when in Advanced User Mode (see Setup Menu Tab: User Mode.)

To change the Temp Offset setting:

1.Make sure you are in Advanced User Mode, then highlight Temp Offset on the Setup menu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Temp Offset setting. (-10.0 to +10.0 degrees, Default = 0)

45

46

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Operations Manual Table of Contents WwwThank You!..reelschel matic..comAccessories Menu Tab Troubleshooting Alarms Menu TabSetup Menu Tab Sonar Menu TabQuadraBeam Sonar Single Beam SonarDualBeam Plus Sonar Hard Bottom WwwWhat’s On..reelschelthe Disp ay matic..comBait Ball Soft BottomSonar View Sonar ViewUnderstanding Sonar History Sonar Zoom View Sonar Zoom ViewFull range view 200/83 kHz Split Sonar View Big Digits ViewDualBeam Plus and QuadraBeamTM Only Big Digits ViewDigital readouts in the Side Beam View cannot be customized Bottom PresentationQuadraBeamTM Only Side Beam ViewView Key POWER/LIGHT KeyKey Functions WAY Cursor Control Key Exit KeyMenu System AccessorymBusaticPowering Up the Unit Start-Up Options Menu Normal OperationWith PC Connect Cable Only System StatusPC Connect Sensitivity To adjust the SensitivityTo adjust the Upper Range Upper RangeTo adjust the Chart Speed Chart SpeedTo adjust the Lower Range To adjust the Bottom ViewSonar Zoom View Only To adjust the Zoom LevelSonar Menu Tab Highlight Zoom Level on the Sonar X-PressTMMenuHighlight Beam Select on the Sonar main menu Fish ID+TMTo use Beam Select To turn Fish ID+ on or offKHz Balance Real Time Sonar RTS WindowKHz Sensitivity Surface Clutter To change the Depth Lines settingTo change the Surface Clutter setting AdvancedTransducer Select Max DepthWater Type Low Battery Alarm Depth AlarmFish ID Alarm Alarm ToneUnits Distance Units DepthUnits Temp Restore Defaults User ModeTriplog Reset LanguageTo Select Views TemperatureSelect Readouts Advanced, Sonar View OnlyDepth Offset To change the Depth Offset settingTo change the Temp Offset setting Temp OffsetNmea Output Accessories Menu TabTo change the Speed Calibration setting Advanced, with Temp/Speed OnlyControl head loses power at high speeds Display ProblemsProblem Possible Cause Matrix Fishing System Accessories IsolationSpecifications Contact Humminbird
Related manuals
Manual 31 pages 15.56 Kb
Top Page Image Contents