Honeywell TE821W Programming Time Alarms, Disable/Enable Snooze function, Disable alarms

Page 25

Note: Press SET button anytime during alarm programming mode to return to the default clock display.

Programming Time Alarms

With the Clock and Alarm icon flashing, press the ALARM/CHART button to select the desired alarm.

•Press and hold ALARM/CHART button until the hour digit will flash

•Set the alarm hour using UP or DOWN arrow button. Press and hold either button for quick digit advance.

•Press ALARM/CHART to confirm selection.

•Set the alarm minutes using UP or DOWN arrow button. Press and hold either button for quick digit advance.

•Press ALARM/CHART button to confirm selection.

•Set a Snooze interval (both alarms share same snooze time duration) using UP or DOWN arrow button. Press and hold either button for quick digit advance.

•Press ALARM/CHART button to confirm your selection.

After programming is completed, the display will return to the alarm selection screen.

Disable/Enable Snooze function

To enable a snooze function press LIGHT/SNOOZE button.

Note: Alarm will automatically “snooze” if no buttons are pressed after the alarm sounds for 2 minutes. This will occur three times only.

Disable alarm(s):

Press ALARM/CHART button to disable the alarm (s).

Note: For weekday alarm, pressing ALARM/CHART button will only disable the alarm for the current day. The alarm will activate again on the next day, Monday through Friday.

Atomic Time Reception

The purpose of the atomic clock is to provide consistently accurate time and date automatically. The radio controlled clock searches for, and periodically synchronizes to, the NIST (National Institute of Standards and Technology) Atomic clock signal transmitted from Colorado, throughout the entire continental United States.

•During night-time hours, atmospheric conditions improve radio signal reception. A single daily reception is sufficient enough to keep the clock accuracy within milliseconds.

•Unit should be positioned 8 feet (2 meters) from interference sources such as a TV, computer, microwave, etc.

•The signal reception is weakened within concrete walls found in basements or office buildings. Place the unit near the window for best reception.

•It takes between 24 and 72 hours for the clock to receive an atomic time signal reception

Once the atomic time signal is received, the date and time will be set automatically, and the icon will appear. Your atomic

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Honeywell Appendix City Codes Specifications Table of ContentsInstallation Standard Package ContentsIntroduction Before you beginThermo-Hygrometer Sensor TS33C FeaturesPlacement tips Battery installationMounting Rain Gauge TS906 Anemometer wind sensor TS805 Wind Vane Assembly Battery CoverTime Main UnitWeather DisplayAvoid placing the main unit in the following areas Buttons and Controls Selects the next available window counter-clockwise Clock and Alarms Window Clock and Calendar Displays Initial Set upOperation and Window Selection Initial Settings City, Time, Date and Language Selecting Clock and Alarm WindowPressure and Weather Forecast Window Custom Weather Station SettingsSelect Pressure and Weather Forecast Window Changing or Setting Sea Level PressurePressure and Altitude Information Changing Pressure and Altitude ParametersViewing the Pressure, Temperature and Humidity Bar Charts Changing or Setting AltitudeViewing the Moon Phase History Viewing the Sea Level Pressure HistoryMoon Phase Diagram Weather Forecast Displays Viewing Temperature and Humidity for each Channel Temperature and Humidity WindowTemperature and Dew Point Displays Channel Auto-Scan DisplayTemperature Alarm Temperature in Celsius or FahrenheitProgramming Upper and Lower limits for Temperature Alarm Disabling Temperature Alarm levelsSetting Rain Display inches or mm Rainfall Memory ResetSetting up Daily Rainfall Alert Selecting Rain WindowSetting Wind Speed in km/h, mph, m/s or knots Configuring Wind DisplayDisabling the Daily Rainfall Alert Wind WindowEnable/Disable Time Alarms Resetting the Wind Statistics MemoryEnabling or Disabling the Wind Alerts Wind Alert programmingDisable/Enable Snooze function Programming Time AlarmsDisable alarms Atomic Time ReceptionRemote Sensor Status Memory Reset ProcedureActivate Search for Remote Sensors Troubleshooting MaintenanceWeather forecast is inaccurate Appendix City CodesPage Specifications Battery life alkaline Power 12 AA Batteries includedWind Direction Wind SpeedDimensions Weight without batteriesDeclaration of Conformity
Related manuals
Manual 33 pages 7.28 Kb
Top Page Image Contents