Garmin TR-1 manual Dual Helm Boats Only, Hydraulic Layout Dual Helm

Page 7

Hydraulic Layout Dual Helm

 

BALANCED CYLINDER

Starboard

Port Fitting

Fitting

 

 

Dual Helm Boats (Only)

 

Hydraulic Layout

 

(For Single Helm Stations; Please see previous page)

*Shadow Drive

1) Mount horizontally and as level as possible

 

2) May be located in the Port or Starboard Hydraulic lines

 

3) Use a length of hose between helm and Shadow Drive Valve

 

4) DO NOT install the Shadow Drive Valve directly to the helm

 

5) Tee fitting that join helms MUST BE IN FRONT of Shadow

 

Drive valve in order for both helms to be able to activate

 

Shadow Drive (Dual Helm Stations Only)

MotorPump &

Unbalanced Cyl.

Unbalanced Valve

Pump &

Motor

NOTE: UNBALANCED CYLINDER REQUIRES

UNBALANCED VALVE ON PUMP.

Lower Helm

P R S

�������������������������������������������������� ����������������������������������������������������� ��������������������������������������������������� ���������������������������������������������� �������������������������

Upper Helm

P R S

P= Port

R= Return

S= Starboard

*Shadow Drive

7

Image 7
Contents TR-1 Autopilots Safety Contents 120-2525-00 120-2510-00 TR-1 Gladiator 1.2 or 2.0 Pump and ECU Parts ListHydraulic Layout for SeaStar Power Assisted Helms SeaStar Power AssistHydraulic Layout Single Helm Single Helm Boats OnlyHydraulic Layout Dual Helm Dual Helm Boats OnlyElectrical Layout Section II Setup Gladiator Installation & SetupSection IV Setup Codes Battery Connections. See Installation Overview and Check ListPreparation For Installation TR-1 Gladiator SpecificationsUnbalanced Kit These are examples of cylinders that Need an unbalanced kitProtection Unbalanced Valve adjustment and calibration Installation of Unbalanced ValveThese are examples of cylinders that Unbalanced Kit Pump Head Up Horizontally Installation Of Pump UnitExample Step two Placing ball in bracket Installation of Compass BallStep Three Adjusting Compass Ball Verify All Connections Prior to Applying power Installation Of Electronic Control Unit ECUNmea 0183 Connections Non-Compliant Nmea 0183 Devices Electrical Connections Installation Of Shadow Drive Valve Single Helm StationPump Motor Installation Of Shadow Drive Valve Dual Helm StationCompass Ball Horn Red + Orange + Installation Of Warning HornInstallation of On/Off Switch Using Waterproof Bezel Installation of Deckmount On/Off SwitchCorded Mount Flush Mount Installation Of HandheldPart Numbers 120-2045-04 ’s Gasoline Tachometry ConnectionsEvinrude E-Tech Bleeding Hydraulics Battery ConnectionsDockside Setup and Sea Trial Setup of Autopilot Step D. Release Select Load button To start Compass calibrationChevron button two times, and light up #5 LED With The GPS Connected to Autopilot Set NorthFine Tuning. Optional Trouble Shooting Guide How to Change Parameters of Setup Codes Description Code Values of the Parameters Factory Defaults Table of Setup Codes and Values of the ParametersDescription Code Table of Setup Codes and ParametersTachometer Codes Garmin GPS Connection GuideModel From GPS To Autopilot Nmea Out Manufacturer FurunoLowrance HummingbirdNorthStar MagellanRayMarine Simrad From GPS To Autopilot Nmea Out ManufacturerChapter Installation of Wireless RemoteParts List Wireless Two Button Description Qty Qty Parts List Wireless Five Button DescriptionThank You IntroductionKeypad push-button functions Wireless Remote Functions, Two ButtonKeypad push-button functions Wireless Remote Functions, Five ButtonWireless Installation Installation ConsiderationsAntenna Installation Security Codes Replacement Remote KeypadsChanging Batteries Limited Warranty 906-2520-00 Version H 110107
Related manuals
Manual 13 pages 3.61 Kb Manual 48 pages 48.1 Kb